LSM6DSTX datasheet(96/175 Pages) STMICROELECTRONICS

96 / 175 page

11.11

SPI2_CTRL1_OIS (70h)

OIS configuration register. The auxiliary SPI interface can write this register when the OIS_CTRL_FROM_UI bit in

the FUNC_CFG_ACCESS (01h) register is equal to 0 (SPI2 full-control mode). This register is read-only when the

OIS_CTRL_FROM_UI bit is equal to 1 (primary IF full-control mode) and shows the content of the UI_INT_OIS

(6Fh) register.

Table 218. SPI_CTRL1_OIS register

0(1)

LVL1_OIS

SIM_OIS

Mode4_EN

FS1_G_

OIS

FS0_G_

OIS

FS_125_

OIS

OIS_EN_

SPI2

1. This bit must be set to 0 for the correct operation of the device.

Table 219. SPI_CTRL1_OIS register description

LVL1_OIS

Enables level-sensitive trigger mode on the OIS chain. Default value: 0

SIM_OIS

SPI2 3- or 4-wire interface. Default value: 0

(0: 4-wire SPI2;

1: 3-wire SPI2)

Mode4_EN

Enables the accelerometer OIS chain. OIS outputs are available through SPI2 in registers

SPI2_OUTX_L_A_OIS (28h) and SPI2_OUTX_H_A_OIS (29h) through SPI2_OUTZ_L_A_OIS (2Ch) and

SPI2_OUTZ_H_A_OIS (2Dh) and SPI2_STATUS_REG_OIS (1Eh).

Note: OIS_EN_SPI2 must be enabled (that is, set to 1) to enable also the accelerometer OIS chain.

FS[1:0]_G_OIS

Selects the gyroscope OIS chain full-scale

(00: ± 250 dps;

01: ±500 dps;

10: ±1000 dps;

11: ±2000 dps)

FS_125_OIS

Selects the gyroscope OIS chain full-scale ±125 dps

(0: FS selected through bits FS[1:0]_OIS_G;

1: ±125 dps)

OIS_EN_SPI2

Enables the OIS chain data processing for gyro in mode 3 and mode 4 (mode4_en = 1) and accelerometer

data in and mode 4 (mode4_en = 1).

When the OIS chain is enabled, the OIS outputs are available through the SPI2 in registers

SPI2_OUTX_L_G_OIS (22h) and SPI2_OUTX_H_G_OIS (23h) through SPI2_OUTZ_L_G_OIS (26h) and

SPI2_OUTZ_H_G_OIS (27h) and STATUS_REG (1Eh) and SPI2_STATUS_REG_OIS (1Eh), and LPF1 is

dedicated to this chain.

DEN mode selection can be done using the LVL1_OIS bit of register UI_CTRL1_OIS (70h) and the LVL2_OIS bit

of register UI_INT_OIS (6Fh).

DEN mode on the OIS path is active in the gyroscope only.

Table 220. DEN mode selection

LVL1_OIS, LVL2_OIS

DEN mode

Level-sensitive trigger mode is selected

Level-sensitive latched mode is selected

LSM6DSTX

SPI2_CTRL1_OIS (70h)

DS14039 - Rev 1

page 96/175

LSM6DSTX 数据表(PDF) 96 Page - STMicroelectronics

LSM6DSTX 数据表(HTML) 96 Page - STMicroelectronics

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100 ...More

数据表下载