| 数据搜索系统,热门电子元器件搜索 |
|
PPC34C60 数据表(PDF) 49 Page - SMSC Corporation |
|
|
|||||||||||||||||||||||||||||
PPC34C60 数据表(HTML) 49 Page - SMSC Corporation |
|
49 / 58 page ![]() SMSC DS – PPC34C60 Page 49 Rev. 06/01/2001 ADVANCED INFORMATION FIGURE 20 - ECP REVERSE DATA TRANSFER TIMING (ECP DATA READ, PARALLEL PORT SIGNALS) Note: The optional use of the nERR (nFAULT) line to "hint" to the Host that the peripheral has data to send to the Host is not supported in the PPC34C60. The driver should ignore any activity on this line. The PPC34C60 supports reverse data transfers only (not reverse command transfers) and, therefore, always asserts the BSY (nCMD) signal during reverse transfers. See ECP Reverse Data Transfer Timing Parameters. ECP REVERSE DATA TRANSFER TIMING (ECP DATA READ, PARALLEL PORT SIGNALS) PARAMETER MIN TYP MAX UNITS t1 To prepare for an ECP reverse channel transfer the Host tri- states the parallel data lines HD[0:7] and asserts nALF at the same time. Next the Host asserts nINIT to initiate an ECP bus reversal. The PPC34C60 requires this amout of time between these events. 0 ns t2 The PPC34C60 acknowledges the bus reversal by deasserting the PE signal. At this point in time the parallel port bus is in the reverse idle state. 208 [5 SCLK] 334 [8 SCLK] ns t3 Along with deasserting the PE signal the PPC34C60 takes control of the parallel port data bus HD[0:7]. The data on this bus remains undefined until the PPC34C60 has accessed and placed a data byte on the bus. Along with driving the data lines with valid data, the PPC34C60 asserts BSY to indicate that this is a data transfer. 0 1,084 [13 BCLK] ns t4 After placing data on the parallel port data lines the PPC34C60 asserts nACK to inform the Host that valid data is available. 125 [3 SCLK] 167 [4 SCLK] ns t5 Next, the Host will acknowledge that it is ready for the data by deasserting nALF. 50 infinite ns t6 Now the PPC34C60 will deassert nACK in response to the Host. The Host will latch the data on HD[0:7] on this rising edge of nACK. 125 [3 SCLK] 167 [4 SCLK] ns t7 The Host completes the ECP reverse transfer, acknowledging that it has accepted the data byte by asserting nALF. 50ns 1s VALID DATA t3 t8 t9 t11 t5 t7 t1 t4 t6 t2 t10 HD[0:7] nSTB H nALF H nSEL H nINIT H BSY P nACK P PE P SLCT P nERR P DATA |
|
链接网址 |
| ALLDATASHEET是否为您带来帮助? [ DONATE ] |
关于 Alldatasheet | 广告服务 | 联系我们 | 隐私政策 | 数据表链接 | 链接交换 | 制造商名单 All Rights Reserved©Alldatasheet.com |
| Russian : Alldatasheetru.com | Korean : Alldatasheet.co.kr | Spanish : Alldatasheet.es | French : Alldatasheet.fr | Italian : Alldatasheetit.com Portuguese : Alldatasheetpt.com | Polish : Alldatasheet.pl | Vietnamese : Alldatasheet.vn Indian : Alldatasheet.in | Mexican : Alldatasheet.com.mx | British : Alldatasheet.co.uk | New Zealand : Alldatasheet.co.nz |
|
Family Site : ic2ic.com |
icmetro.com |