T48C862-R4 datasheet(67/107 Pages) ATMEL

67 / 107 page

T48C862-R4 [Preliminary]

4551C–4BMCU–01/04

Synchronous Serial

Interface (SSI)

SSI Features:

•With Timer 1

–

2- and 3-wire NRZ

–

2-wire mode multi-chip link mode (MCL), additional internal 2-wire link for

multi-chip packaging solutions

•With Timer 2

–

Biphase modulation

–

Manchester modulation

–

Pulse-width demodulation

–

Burst modulation

•With Timer 3

–

Pulse-width modulation (PWM)

–

FSK modulation

–

Biphase demodulation

–

Manchester demodulation

–

Pulse-width demodulation

–

Pulse position Demodulation

SSI Peripheral Configuration

The synchronous serial interface (SSI) can be used either for serial communication with

external devices such as EEPROMs, shift registers, display drivers, other microcontrol-

lers, or as a means for generating and capturing on-chip serial streams of data. External

data communication takes place via the Port 4 (BP4),a multi-functional port which can

be software configured by writing the appropriate control word into the P4CR register.

The SSI can be configured in any of the following ways:

2-wire external interface for bi-directional data communication with one data ter-

minal and one shift clock. The SSI uses the Port BP43 as a bi-directional serial

data line (SD) and BP40 as shift clock line (SC).

3-wire external interface for simultaneous input and output of serial data, with a

serial input data terminal (SI), a serial output data terminal (SO) and a shift clock

(SC). The SSI uses BP40 as shift clock (SC), while the serial data input (SI) is

applied to BP43 (configured in P4CR as input). Serial output data (SO) in this

case is passed through to BP42 (configured in P4CR to T2O) via the Timer 2

output stage (T2M2 configured in mode 6).

Timer/SSI combined modes – the SSI used together with Timer 2 or Timer 3 is

capable of performing a variety of data modulation and demodulation functions

(see section Timer). The modulating data is converted by the SSI into a continu-

ous serial stream of data which is in turn modulated in one of the timer functional

blocks. Serial demodulated data can be serially captured in the SSI and read by

the controller. In the Timer 3 modes 10 and 11 (demodulation modes) the SSI

can only be used as demodulator.

Multi-chip link (MCL) – the SSI can also be used as an interchip data interface for

use in single package multi-chip modules or hybrids. For such applications, the

SSI is provided with two dedicated pads (MCL_SD and MCL_SC) which act as a

two-wire chip-to-chip link. The MCL can be activated by the MCL control bit.

Should these MCL pads be used by the SSI, the standard SD and SC pins are

not required and the corresponding Port 4 ports are available as conventional

data ports.

T48C862-R4 数据表(PDF) 67 Page - ATMEL Corporation

T48C862-R4 数据表(HTML) 67 Page - ATMEL Corporation

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100 ...More

数据表下载