T48C862-R4 datasheet(52/107 Pages) ATMEL

52 / 107 page

T48C862-R4 [Preliminary]

4551C–4BMCU–01/04

Timer 2 Mode Register 2

(T2M2)

Address: "7"hex - Subaddress: "2"hex

Table 19.

Timer 2 Output Select Bits

If one of these output modes is used the T2O alternate function of Port 4 must also be

activated.

Timer 2 Compare and

Compare Mode Registers

Timer 2 has two separate compare registers, T2CO1 for the 4-bit stage and T2CO2 for

the 8-bit stage of Timer 2. The timer compares the contents of the compare register cur-

rent counter value and if it matches it generates an output signal. Dependent on the

timer mode, this signal is used to generate a timer interrupt, to toggle the output flip-flop

as SSI clock or as a clock for the next counter stage.

In the 12-bit timer mode, T2CO1 contains bits 0 to 3 and T2CO2 bits 4 to 11 of the 12-bit

compare value. In all other modes, the two compare registers work independently as a

4- and 8-bit compare register.

When assigned to the compare register a compare event will be suppressed.

Bit 3Bit 2Bit 1Bit 0

T2TOP

T2OS2

T2OS1

T2OS0

Reset value: 1111b

T2TOP

imer 2 Toggle Output Preset

This bit allows the programmer to preset the Timer 2 output T2O.

T2TOP = 0, resets the toggle outputs with the write cycle (M2 = 0)

T2TOP = 1, sets toggle outputs with the write cycle (M2 = 1)

Note: If T2R = 1, no output preset is possible

T2OS2

imer 2 Output Select bit 2

T2OS1

imer 2 Output Select bit 1

T2OS0

imer 2 Output Select bit 0

Output Mode

T2OS2

T2OS1

T2OS0

Clock Output (POUT)

111

Toggle mode: a Timer 2 compare match

toggles the output flip-flop (M2) -> T2O

110

Duty cycle burst generator 1: the DCG output

signal (DCG0) is given to the output and

gated by the output flip-flop (M2)

101

Duty cycle burst generator 2: the DCG output

signal (DCGO) is given to the output and

gated by the SSI internal data output (SO)

100

Biphase modulator: Timer 2 modulates the

SSI internal data output (SO) to Biphase

code

011

Manchester modulator: Timer 2 modulates

the SSI internal data output (SO) to

Manchester code

010

SSI output: T2O is used directly as SSI

internal data output (SO)

PWM mode: an 8/12-bit PWM mode

Not allowed

T48C862-R4 数据表(PDF) 52 Page - ATMEL Corporation

T48C862-R4 数据表(HTML) 52 Page - ATMEL Corporation

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100 ...More

数据表下载

链接网址

T48C862-R4 数据表(PDF) 52 Page - ATMEL Corporation

T48C862-R4 数据表(HTML) 52 Page - ATMEL Corporation

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100 ...More

数据表 下载

链接网址

数据表下载