ST7MC1K2-Auto datasheet(150/371 Pages) STMICROELECTRONICS

150 / 371 page

Obsolete

Product(s)

- Obsolete

Product(s)

On-chip peripherals

ST7MC1K2-Auto, ST7MC1K6-Auto, ST7MC2S4-Auto, ST7MC2S6-Auto

150/371

A muted receiver may be woken up in one of the following ways:

●

by idle line detection if the WAKE bit is reset,

●

by address mark detection if the WAKE bit is set.

Idle line detection

Receiver wakes up by idle line detection when the receive line has recognized an idle line.

Then the RWU bit is reset by hardware but the IDLE bit is not set.

This feature is useful in a multiprocessor system when the first characters of the message

determine the address and when each message ends by an idle line. As soon as the line

becomes idle, every receivers is woken up and the first characters of the message which

indicates the addressed receiver are analyzed. The receivers which are not addressed set

RWU bit to enter in mute mode. Consequently, they do not treat the next characters

constituting the next part of the message. At the end of the message, an idle line is sent by

the transmitter: this wakes up every receiver which are ready to analyse the addressing

characters of the new message.

In such a system, the inter-characters space must be smaller than the idle time.

Address mark detection

Receiver wakes up by address mark detection when it receives a ‘1’ as the most significant

bit of a word, thus indicating that the message is an address. The reception of this particular

word wakes up the receiver, resets the RWU bit and sets the RDRF bit, which allows the

receiver to receive this word normally and to use it as an address word.

This feature is useful in a multiprocessor system when the most significant bit of each

character (except for the break character) is reserved for address detection. As soon as the

receivers receive an address character (most significant bit = ‘1’), the receivers are woken

up. The receivers which are not addressed set the RWU bit to enter in mute mode.

Consequently, they do not treat the next characters constituting the next part of the

message.

Parity control

Hardware byte parity control (generation of parity bit in transmission and parity checking in

reception) can be enabled by setting the PCE bit in the SCICR1 register. Depending on the

character format defined by the M bit, the possible SCI character formats are as listed in

Table 59.

Note:

In case of wake-up by an address mark, the MSB bit of the data is taken into account and

not the parity bit

Table 59.

Character formats

M bit

PCE bit

Character format

0| SB(1) | 8 bit data | STB(2) |

SB = start bit

STB = stop bit

| SB | 7-bit data | PB(3) | STB |

PB = parity bit

| SB | 9-bit data | STB |

| SB | 8-bit data | PB | STB |

Obsolete

Product(s)

- Obsolete

Product(s)

ST7MC1K2-Auto 数据表(PDF) 150 Page - STMicroelectronics

ST7MC1K2-Auto 数据表(HTML) 150 Page - STMicroelectronics

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100 ...More

数据表下载

链接网址

ST7MC1K2-Auto 数据表(PDF) 150 Page - STMicroelectronics

ST7MC1K2-Auto 数据表(HTML) 150 Page - STMicroelectronics

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100 ...More

数据表 下载

链接网址

数据表下载