LPC802 datasheet(52/83 Pages) NXP

52 / 83 page

LPC802

All information provided in this document is subject to legal disclaimers.

Product data sheet

Rev. 1.6 — 27 April 2018

52 of 83

NXP Semiconductors

LPC802

32-bit ARM Cortex-M0+ microcontroller

[1]

See the I2C-bus specification UM11045 for details.

[2]

Parameters are valid over operating temperature range unless otherwise specified.

[3]

tHD;DAT is the data hold time that is measured from the falling edge of SCL; applies to data in transmission

and the acknowledge.

[4]

A device must internally provide a hold time of at least 300 ns for the SDA signal (with respect to the

VIH(min) of the SCL signal) to bridge the undefined region of the falling edge of SCL.

[5]

Cb = total capacitance of one bus line in pF.

[6]

The maximum tf for the SDA and SCL bus lines is specified at 300 ns. The maximum fall time for the SDA

output stage tf is specified at 250 ns. This allows series protection resistors to be connected in between the

SDA and the SCL pins and the SDA/SCL bus lines without exceeding the maximum specified tf.

[7]

The maximum tHD;DAT could be 3.45 s and 0.9 s for Standard-mode and Fast-mode but must be less than

the maximum of tVD;DAT or tVD;ACK by a transition time (see UM10204). This maximum must only be met if

the device does not stretch the LOW period (tLOW) of the SCL signal. If the clock stretches the SCL, the

data must be valid by the set-up time before it releases the clock.

[8]

tSU;DAT is the data set-up time that is measured with respect to the rising edge of SCL; applies to data in

transmission and the acknowledge.

[9]

A Fast-mode I2C-bus device can be used in a Standard-mode I2C-bus system but the requirement

tSU;DAT = 250 ns must then be met. This will automatically be the case if the device does not stretch the

LOW period of the SCL signal. If such a device does stretch the LOW period of the SCL signal, it must

output the next data bit to the SDA line tr(max) + tSU;DAT = 1000 + 250 = 1250 ns (according to the

Standard-mode I2C-bus specification) before the SCL line is released. Also the acknowledge timing must

meet this set-up time.

tHD;DAT

data hold time

[3][4][7]

Standard-mode

s

Fast-mode

s

tSU;DAT

data set-up

time

[8][9]

Standard-mode

250

Fast-mode

100

Table 20.

Dynamic characteristic: I2C-bus pins[1]

Tamb = 40 C to +105 C; values guaranteed by design.[2]

Symbol

Parameter

Conditions

Min

Max

Unit

Fig 26. I2C-bus pins clock timing

LPC802 数据表(PDF) 52 Page - NXP Semiconductors

LPC802 数据表(HTML) 52 Page - NXP Semiconductors

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83

数据表下载