| 数据搜索系统,热门电子元器件搜索 |
|
TMP86FS49AIUG 数据表(PDF) 259 Page - Toshiba Semiconductor |
|
|
|||||||||||||||||||||||||||||
TMP86FS49AIUG 数据表(HTML) 259 Page - Toshiba Semiconductor |
|
259 / 296 page ![]() Page 243 TMP86FS49AIUG 20.6.2 Flash Memory Writing Mode (Operation command: 30H) Table 20-8 shows flash memory writing mode process. Note 1: “xxH × 3” indicates that the device enters the halt condition after sending 3 bytes of xxH. For details, refer to " 20.7 Error Code ". Note 2: Refer to " 20.9 Intel Hex Format (Binary) ". Note 3: Refer to " 20.8 Checksum (SUM) ". Note 4: Refer to " 20.10 Passwords ". Note 5: If addresses from FFE0H to FFFFH are filled with “FFH”, the passwords are not compared because the device is consid- ered as a blank product. Transmitting a password string is not required. Even in the case of a blank product , it is required to specify the password count storage address and the password comparison start address. Transmit these data from the external controller. If a password error occurs due to incorrect password count storage address or password comparison start address, TMP86FS49AIUG stops UART communication and enters the halt condition. Therefore, when a password error occurs, initialize TMP86FS49AIUG by the RESET pin and reactivate the serial ROM mode. Note 6: If the read protection is enabled or a password error occurs, TMP86FS49AIUG stops UART communication and enters the halt confition. In this case, initialize TMP86FS49AIUG by the RESET pin and reactivate the serial ROM mode. Note 7: If an error occurs during the reception of a password address or a password string, TMP86FS49AIUG stops UART com- munication and enters the halt condition. In this case, initialize TMP86FS49AIUG by the RESET pin and reactivate the serial PROM mode. Table 20-8 Flash Memory Writing Mode Process Transfer Byte Transfer Data from External Controller to TMP86FS49AIUG Baud Rate Transfer Data from TMP86FS49AIUG to External Controller BOOT ROM 1st byte 2nd byte Matching data (5Ah) - 9600 bps 9600 bps - (Automatic baud rate adjustment) OK: Echo back data (5AH) Error: Nothing transmitted 3rd byte 4th byte Baud rate modification data (See Table 20-4) - 9600 bps 9600 bps - OK: Echo back data Error: A1H × 3, A3H × 3, 62H × 3 (Note 1) 5th byte 6th byte Operation command data (30H) - Modified baud rate Modified baud rate - OK: Echo back data (30H) Error: A1H × 3, A3H × 3, 63H × 3 (Note 1) 7th byte 8th byte Password count storage address bit 15 to 08 (Note 4) Modified baud rate - OK: Nothing transmitted Error: Nothing transmitted 9th byte 10th byte Password count storage address bit 07 to 00 (Note 4) Modified baud rate - OK: Nothing transmitted Error: Nothing transmitted 11th byte 12th byte Password comparison start address bit 15 to 08 (Note 4) Modified baud rate - OK: Nothing transmitted Error: Nothing transmitted 13th byte 14th byte Password comparison start address bit 07 to 00 (Note 4) Modified baud rate - OK: Nothing transmitted Error: Nothing transmitted) 15th byte : m’th byte Password string (Note 5) - Modified baud rate - OK: Nothing transmitted Error: Nothing transmitted m’th + 1 byte : n’th - 2 byte Intel Hex format (binary) (Note 2) Modified baud rate - - n’th - 1 byte - Modified baud rate OK: SUM (Upper byte) (Note 3) Error: Nothing transmitted n’th byte - Modified baud rate OK: SUM (Lower byte) (Note 3) Error: Nothing transmitted n’th + 1 byte (Wait state for the next operation com- mand data) Modified baud rate - |
|
链接网址 |
| ALLDATASHEET是否为您带来帮助? [ DONATE ] |
关于 Alldatasheet | 广告服务 | 联系我们 | 隐私政策 | 数据表链接 | 链接交换 | 制造商名单 All Rights Reserved©Alldatasheet.com |
| Russian : Alldatasheetru.com | Korean : Alldatasheet.co.kr | Spanish : Alldatasheet.es | French : Alldatasheet.fr | Italian : Alldatasheetit.com Portuguese : Alldatasheetpt.com | Polish : Alldatasheet.pl | Vietnamese : Alldatasheet.vn Indian : Alldatasheet.in | Mexican : Alldatasheet.com.mx | British : Alldatasheet.co.uk | New Zealand : Alldatasheet.co.nz |
|
Family Site : ic2ic.com |
icmetro.com |