数据搜索系统,热门电子元器件搜索
  Chinese  ▼
ALLDATASHEETCN.COM

X  

ZUSBOPTSC01ZAC 数据表(PDF) 117 Page - Zilog, Inc.

部件名 ZUSBOPTSC01ZAC
功能描述  Z8 Encore-R Motor Control Flash MCUs
PDF  402 Pages
Scroll/Zoom Zoom In 100%  Zoom Out
制造商  ZILOG [Zilog, Inc.]
网页  http://www.zilog.com
标志 ZILOG - Zilog, Inc.

ZUSBOPTSC01ZAC 数据表(HTML) 117 Page - Zilog, Inc.

Back Button ZUSBOPTSC01ZAC Datasheet HTML 113Page - Zilog, Inc. ZUSBOPTSC01ZAC Datasheet HTML 114Page - Zilog, Inc. ZUSBOPTSC01ZAC Datasheet HTML 115Page - Zilog, Inc. ZUSBOPTSC01ZAC Datasheet HTML 116Page - Zilog, Inc. ZUSBOPTSC01ZAC Datasheet HTML 117Page - Zilog, Inc. ZUSBOPTSC01ZAC Datasheet HTML 118Page - Zilog, Inc. ZUSBOPTSC01ZAC Datasheet HTML 119Page - Zilog, Inc. ZUSBOPTSC01ZAC Datasheet HTML 120Page - Zilog, Inc. ZUSBOPTSC01ZAC Datasheet HTML 121Page - Zilog, Inc. Next Button
Zoom Inzoom in Zoom Outzoom out
 117 / 402 page
background image
PS024604-1005
P R E L I M I N A R Y
Timer Operating Modes
Z8FMC16100 Series Flash MCU
Product Specification
95
c. Set the prescale value.
d. If using the Timer Output alternate function, set the initial output level (High or
Low) via the TPOL bit.
e. Set the INTERRUPT mode.
2. Write to the Timer High and Low Byte registers to set the starting count value.
3. Write to the Timer Reload High and Low Byte registers to set the reload value.
4. If appropriate, enable the timer interrupt and set the timer interrupt priority by writing
to the relevant interrupt registers.
5. If using the Timer Output function, configure the associated GPIO port pin for the
Timer Output alternate function.
6. Write to the Timer Control 1 Register to enable the timer. Counting does not start until
the appropriate input transition occurs.
The timer period is calculated by the following equation (Start Value is typically = 1):
The one-shot delay from input trigger to output includes the above-defined time-out
period, plus an additional delay of 2–3 system clock cycles, due to the synchronization of
the input trigger.
Continuous Mode
In CONTINUOUS mode, the timer counts up to the 16-bit reload value stored in the Timer
Reload High and Low Byte registers. After reaching the reload value, the timer generates
an interrupt, the count value in the Timer High and Low Byte registers is reset to 0001h,
and counting resumes. Also, if the Timer Output alternate function is enabled, the Timer
Output pin changes state (from Low to High or from High to Low) after timer reload.
The steps for configuring a timer for CONTINUOUS mode and initiating the count are as
follows:
1. Write to the Timer Control registers to:
a. Disable the timer.
b. Configure the timer for CONTINUOUS mode.
c. Set the prescale value.
Triggered One-Shot Mode Time-Out Period(s) =
(Reload Value – Start Value + 1) x Prescaler
System Clock Frequency (Hz)
Note:



Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100  ...More


数据表 下载

Go To PDF Page


链接网址



ALLDATASHEET是否为您带来帮助?  [ DONATE ] 

关于 Alldatasheet   |   广告服务   |   联系我们   |   隐私政策   |   数据表链接    |   链接交换   |   制造商名单
All Rights Reserved©Alldatasheet.com


Mirror Sites
English : Alldatasheet.com  |   English : Alldatasheet.net  |   Chinese : Alldatasheetcn.com  |   German : Alldatasheetde.com  |   Japanese : Alldatasheet.jp
Russian : Alldatasheetru.com  |   Korean : Alldatasheet.co.kr  |   Spanish : Alldatasheet.es  |   French : Alldatasheet.fr  |   Italian : Alldatasheetit.com
Portuguese : Alldatasheetpt.com  |   Polish : Alldatasheet.pl  |   Vietnamese : Alldatasheet.vn
Indian : Alldatasheet.in  |   Mexican : Alldatasheet.com.mx  |   British : Alldatasheet.co.uk  |   New Zealand : Alldatasheet.co.nz
Family Site : ic2ic.com  |   icmetro.com