AD9520-5SLASHPCBZ datasheet(46/80 Pages) AD

46 / 80 page

AD9520-5

Rev. 0 | Page 46 of 80

SERIAL CONTROL PORT

The AD9520 serial control port is a flexible, synchronous serial

communications port that allows an easy interface with many

industry-standard microcontrollers and microprocessors. The

AD9520 serial control port is compatible with most synchronous

transfer formats, including Philips I2C, Motorola® SPI®, and

Intel® SSR protocols. The AD9520 I2C implementation deviates

from the classic I2C specification on two specifications, and

these deviations are documented in Table 11 of this data sheet.

The serial control port allows read/write access to all registers

that configure the AD9520.

SPI/I²C PORT SELECTION

The AD9520 has two serial interfaces, SPI and I2C. Users can

select either SPI or I2C depending on the states of the three

logic level (high, open, low) input pins, SP1 and SP0. When

both SP1 and SP0 are high, the SPI interface is active. Otherwise,

I2C is active with eight different I2C slave address (seven bits

wide) settings, see Table 35. The four MSBs of the slave address

are hardware coded as 1011, and the three LSBs are programmed

by SP1 and SP0.

Table 35. Serial Port Mode Selection

SP1

SP0

Address

Low

I²C, 1011000

Low

Open

I²C, 1011001

Low

High

I²C, 1011010

Open

Low

I²C, 1011011

Open

I²C, 1011100

Open

High

I²C, 1011101

High

Low

I²C, 1011110

High

Open

I²C, 1011111

High

SPI

I²C SERIAL PORT OPERATION

The AD9520 I2C port is based on the I2C fast mode standard.

The AD9520 supports both I2C protocols: standard mode

(100 kHz) and fast mode (400 kHz).

The AD9520 I2C port has a 2-wire interface consisting of a serial

data line (SDA) and a serial clock line (SCL). In an I2C bus system,

the AD9520 is connected to the serial bus (data bus SDA and

clock bus SCL) as a slave device, meaning that no clock is generated

by the AD9520. The AD9520 uses direct 16-bit (two bytes)

memory addressing instead of traditional 8-bit (one byte) memory

addressing.

I2C Bus Characteristics

Table 36. I2C Bus Definitions

Abbreviation

Definition

Start

Repeated start

Stop

Acknowledge

No acknowledge

Write

Read

One pulse on the SCL clock line is generated for each data bit

transferred.

The data on the SDA line must not change during the high

period of the clock. The state of the data line can change only when

the clock on the SCL line is low.

SDA

SCL

DATA LINE

STABLE;

DATA VALID

CHANGE

OF DATA

ALLOWED

Figure 43. Valid Bit Transfer

A start condition is a transition from high to low on the SDA

line while SCL is high. The start condition is always generated

by the master to initialize the data transfer.

A stop condition is a transition from low to high on the SDA

line while SCL is high. The stop condition is always generated

by the master to end the data transfer.

START

CONDITION

STOP

CONDITION

SDA

SCL

Figure 44. Start and Stop Conditions

A byte on the SDA line is always eight bits long. An acknowledge

bit must follow every byte. Bytes are sent MSB first.

The acknowledge bit is the ninth bit attached to any 8-bit data

byte. An acknowledge bit is always generated by the receiving

device (receiver) to inform the transmitter that the byte has

been received. It is done by pulling the SDA line low during the

ninth clock pulse after each 8-bit data byte.

AD9520-5/PCBZ 数据表(PDF) 46 Page - Analog Devices

AD9520-5/PCBZ 数据表(HTML) 46 Page - Analog Devices

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80

数据表下载

链接网址

AD9520-5/PCBZ 数据表(PDF) 46 Page - Analog Devices

AD9520-5/PCBZ 数据表(HTML) 46 Page - Analog Devices

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80

数据表 下载

链接网址

数据表下载