AD9520-5SLASHPCBZ datasheet(72/80 Pages) AD

72 / 80 page

AD9520-5

Rev. 0 | Page 72 of 80

Reg.

Addr

(Hex) Bit(s) Name

Description

198

[2]

Channel 2 power-down

Channel 2 powers down.

[2] = 0; normal operation (default).

[2] = 1; powered down. (OUT6/OUT6, OUT7/OUT7, and OUT8/OUT8 are put into safe power-

down mode by setting this bit.)

198

[1]

Channel 2 direct-to-output

Connects OUT6, OUT7, and OUT8 to Divider 2 or directly to CLK.

[1] = 0; OUT6, OUT7, and OUT8 are connected to Divider 2 (default).

[1] = 1:

If 0x1E1[0] = 0, the CLK is routed directly to OUT6, OUT7, and OUT8.

If 0x1E1[0] = 1, there is no effect.

198

[0]

Disable Divider 2 DCC

Duty-cycle correction function.

[0] = 0; enable duty-cycle correction (default).

[0] = 1; disable duty-cycle correction.

199

[7:4]

Divider 3 low cycles

Number of clock cycles (minus 1) of the divider input during which the divider output stays

low. A value of 0x0 means that the divider is low for one input clock cycle (default: 0x0).

199

[3:0]

Divider 3 high cycles

Number of clock cycles (minus 1) of the divider input during which the divider output stays

high. A value of 0x0 means that the divider is high for one input clock cycle (default: 0x0).

19A

[7]

Divider 3 bypass

Bypasses and powers down the divider; routes input to divider output.

[7] = 0; use divider (default).

[7] = 1; bypass divider.

19A

[6]

Divider 3 ignore SYNC

Ignore SYNC.

[6] = 0; obey chip-level SYNC signal (default).

[6] = 1; ignore chip-level SYNC signal.

19A

[5]

Divider 3 force high

Forces divider output to high. This requires that ignore SYNC also be set.

[5] = 0; divider output forced to low (default).

[5] = 1; divider output forced to high.

19A

[4]

Divider 3 start high

Selects clock output to start high or start low.

[4] = 0; start low (default).

[4] = 1; start high.

19A

[3:0]

Divider 3 phase offset

Phase offset (default: 0x0).

19B

[2]

Channel 3 power-down

Channel 3 powers down.

[2] = 0; normal operation (default).

[2] = 1; powered down. (OUT9/OUT9, OUT10/OUT10, and OUT11/OUT11 are put into safe

power-down mode by setting this bit.)

19B

[1]

Channel 3 direct-to-output

Connects OUT9, OUT10, and OUT11 to Divider 3 or directly to CLK.

[1] = 0; OUT9, OUT10, and OUT11 are connected to Divider 3 (default).

[1] = 1:

If 0x1E1[0] = 0, the CLK is routed directly to OUT9, OUT10, and OUT11.

If 0x1E1[0] = 1, there is no effect.

19B

[0]

Disable Divider 3 DCC

Duty-cycle correction function.

[0] = 0; enable duty-cycle correction (default).

[0] = 1; disable duty-cycle correction.

AD9520-5/PCBZ 数据表(PDF) 72 Page - Analog Devices

AD9520-5/PCBZ 数据表(HTML) 72 Page - Analog Devices

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80

数据表下载