RM0319 datasheet(323/368 Pages) STMICROELECTRONICS

323 / 368 page

RM0319

Power, reset and clock control

Doc ID 022640 Rev 3

323/368

30.1.1

SLEEP

During this mode the system clocks, HCLK and CLK, are disabled and the system controller

clock SCLK is driven from a low speed oscillator (nominally 32 768 Hz). When either a FIQ

or an IRQ interrupt is activated (through the VIC) the system moves into the DOZE mode.

Additionally, the required operating mode in the system control register automatically

changes from SLEEP to DOZE.

In SLEEP state, the clock is not provided to CPU. This state maximizes power saving.

The system controller clock is driven by the last selected source in DOZE mode, it could be

RTC or main oscillator.

On interrupt request, normal (IRQ) or fast (FIQ) request, the CPU wakes up and goes in

DOZE. Few clock cycles (less than five) are required for this transition.

To reduce power consumption, it is recommended to switch off all clocks to modules which

are not used for wake-up purpose (see Section 30.4: Reset).

Interrupts enabling wake-up from SLEEP state are:

●

Ethernet

MAC:

possible

disable

the

clock

Ethernet

MAC

(PERIP1_CLK_ENB.gmac_clkenb) using the external clock provided by PHY MAC.

●

USB Device: In this case, the clock to USB Device cannot be switched off

(PERIP1_CLK_ENB.usbdev_clkenb) and AHB since the resume interrupt is registered

by HCLK.

●

RTC: All clocks to internal modules can be switched off (except for RTC).

●

GPIO: All clocks to internal modules can be switched off (except for GPIO).

●

TIMER: All timers if timer clock is not switched off (see PERIP1_CLK_ENB register for

timer clock sources)

Note:

Sleep state is only activated if SCCTRL Mode Ctrl is set to zero and processor is in Wait-for-

Interrupt state.

30.1.2

DOZE (reset state)

DOZE is the first state activated after reset.

During this mode the system clocks, HCLK and CLK, and the system controller clock SCLK

are driven from the output of crystal oscillator (24 MHz) or low frequency oscillator (32 kHz).

The system controller moves into SLEEP mode from DOZE mode only when none of the

mode control bits are set and the processor is in Wait-for-interrupt state. If SLOW mode or

NORMAL mode is required the system moves into the XTAL control transition state to

initialize the crystal oscillator.

SLOW

Running

MAIN Osc. (PLL off)

Self refresh

Internal memory

MAIN Osc.(PLL off)

Active

Internal memory and

external DRAM

NORMAL

Running

PLL1 (Up to 333 MHz)

Active

Internal memory and

exernal DRAM

Table 116.

Power state for asynchronous DRAM system (DRAM clocked by PLL2)

State

ARM

ARM clock

DRAM

Possible code

execution memory

RM0319 数据表(PDF) 323 Page - STMicroelectronics

RM0319 数据表(HTML) 323 Page - STMicroelectronics

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100 ...More

数据表下载