ST10F280 datasheet(46/186 Pages) STMICROELECTRONICS

46 / 186 page

ST10F280

46/186

7 - EXTERNAL BUS CONTROLLER

All of the external memory accesses are per-

formed by the on-chip external bus controller.

The EBC can be programmed to single chip mode

when no external memory is required, or to one of

four different external memory access modes:

– 16-/18-/20-/24-bit addresses 16-bit data, demul-

tiplexed

– 16-/18-/20-/24-bit addresses 16-bit data, multi-

plexed

– 16-/18-/20-/24-bit addresses 8-bit data, multi-

plexed

– 16-/18-/20-/24-bit addresses 8-bit data, demulti-

plexed

In demultiplexed bus modes addresses are output

on PORT1 and data is input/output on PORT0 or

P0L, respectively. In the multiplexed bus modes

both addresses and data use PORT0 for input/

output.

Timing characteristics of the external bus inter-

face (memory cycle time, memory tri-state time,

length of ale and read write delay) are program-

mable giving the choice of a wide range of memo-

ries and external peripherals.

Up to 4 independent address windows may be

defined (using register pairs ADDRSELx / BUS-

CONx) to access different resources and bus

characteristics.

These address windows are arranged hierarchi-

cally where BUSCON4 overrides BUSCON3 and

BUSCON2 overrides BUSCON1. All accesses to

locations not covered by these 4 address windows

are controlled by BUSCON0.

Up to 5 external CS signals (4 windows plus

default) can be generated in order to save exter-

nal glue logic. Access to very slow memories is

supported by a ‘Ready’ function.

A HOLD/HLDA protocol is available for bus arbi-

tration which shares external resources with other

bus masters. The bus arbitration is enabled by

setting bit HLDEN in register PSW. After setting

HLDEN once, pins P6.7...P6.5 (BREQ, HLDA,

HOLD) are automatically controlled by the EBC. In

master mode (default after reset) the HLDA pin is

an output.

By setting bit DP6.7 to’1’ the slave mode is

selected where pin HLDA is switched to input.

This directly connects the slave controller to

another master controller without glue logic.

For applications which require less external mem-

ory space, the address space can be restricted to

1 MByte, 256 KByte or to 64 KByte. Port 4 outputs

all 8 address lines if an address space of 16

MBytes is used, otherwise four, two or no address

lines.

Chip select timing can be made programmable.

By default (after reset), the CSx lines change half

a CPU clock cycle after the rising edge of ALE.

With the

CSCFG

bit set

the

SYSCON

of ALE.

The active level of the READY pin can be set by bit

RDYPOL in the BUSCONx registers. When the

READY function is enabled for a specific address

window, each bus cycle within the window must

be terminated with the active level defined by bit

RDYPOL in the associated BUSCON register.

7.1 - Programmable Chip Select Timing Control

The ST10F280 allows the user to adjust the posi-

tion of the CSx lines changes. By default (after

reset), the CSx lines are changing half a CPU

clock cycle (12.5 ns at fCPU = 40MHz) after the ris-

ing edge of ALE.

With the CSCFG bit set in the SYSCON register,

the CSx lines are changing with the rising edge of

ALE, thus the CSx lines are changing at the same

time the address lines are changing. See Section

19.2

System

Configuration

Registers

for

detailled description of SYSCON register.

ST10F280 数据表(PDF) 46 Page - STMicroelectronics

ST10F280 数据表(HTML) 46 Page - STMicroelectronics

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100 ...More

数据表下载

链接网址

ST10F280 数据表(PDF) 46 Page - STMicroelectronics

ST10F280 数据表(HTML) 46 Page - STMicroelectronics

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100 ...More

数据表 下载

链接网址

数据表下载