TNETX15VE datasheet(25/113 Pages) TI1

25 / 113 page

TNETX15VE

VLAN-ENGINE ADDRESS-LOOKUP DEVICE

SPWS028B – APRIL 1997 – REVISED SEPTEMBER 1997

POST OFFICE BOX 655303

• DALLAS, TEXAS 75265

serial interface I/O register, SIO at 0x0A (DIO)

BIT

NMRST

MCLK

MTXEN

MDATA

MDIOEN

ECLOK

ETXEN

EDATA

Initial Values After Reset

MDIO

EDIO

The SIO register contains the control bits for two serial interfaces to TNETX15VE. Setting the outbound signals

changes the state of the external terminal. Sampling the inbound signals gives the state of the external terminal.

The MII to the PHY devices has a serial management portion. This interface can have multiple masters, and

allows for two way data between master and slave. The interface to the EEPROM is simpler because it is a

dedicated path between one TNETX15VE and its EEPROM, although it is also serial and two way.

BIT

NAME

FUNCTION

MNRST

MII NOT reset. The state of MNRST directly controls the state of the MRESET line (MII reset)

• If MNRST is set to 0: The MRESET line is set to 0.

• If MNRST is set to 1: The MRESET line is set to 1.

This bit is not self-clearing and must be manually deasserted. It can be set low and then immediately set

high. Since every PHY attached to the MII may not have a reset terminal, you need to do MNRST and also

individually reset each PHY through MII commands. The default state of this bit is 0 (MII is in reset). The

MDIOEN bit must be set to drive MRESET.

MCLK

MII SIO clock. MCLK controls the state of the MDCLK terminal. The MDIOEN bit must be set to drive

MDCLK.

• When MCLK is set to 1, MDCLK is set to 1.

• When MCLK is set to 0, MDCLK is set to 0.

MTXEN

MII SIO transmit enable. MTXEN is used with the MDATA bit to read/write information from/to the MDIO

terminal. The MDIOEN bit must be set to drive MDIO.

• When MTXEN is set to 1, the MDIO terminal is driven with the value in the MDATA bit.

• When MTXEN is set to 0, MDATA is loaded with the value in the MDIO terminal.

MDATA

MII SIO data. MDATA is used with MTXEN to read/write information from/to the MDIO terminal.

• When MTXEN is set to 1, MDIO is driven with the value in this bit.

• When MTXEN is set to 0, this bit is loaded with the value on MDIO.

The MDIOEN bit must be set to drive MDIO. The default value of this bit is the value driven on the MDIO

terminal.

MDIOEN

MII SIO data terminal enable. MDIOEN controls the high-Z state of the MDIO, MDCLK, and MRESET

terminals.

• Setting MDIOEN to 1 enables MII.

• Setting MDIOEN to 0 places MII in a high-Z state.

The default state of this bit is 0 (MII disabled)

ECLOK

EEPROM SIO clock. ECLOK controls the state of the ECLK terminal.

• When ECLOK is set to 1, ECLK is set to one.

• When ECLOK is set to 0, ECLK is set to 0.

ETXEN

EEPROM SIO transmit enable. ETXEN controls the direction of the EDIO terminal.

• When ETXEN is set to 1, EDIO is driven with the value in the EDATA bit.

• When ETXEN is set to 0, EDATA is loaded with the value on the EDIO terminal.

EDATA

EEPROM SIO data. EDATA is used to read or write the state of the EDIO terminal.

• When EXTEN is set to 1, EDIO is driven with the value in this bit.

• When EXTEN is set to 0, EDATA is loaded with the value on EDIO.

The default value of this bit is the value driven on the EDIO terminal.

TNETX15VE 数据表(PDF) 25 Page - Texas Instruments

TNETX15VE 数据表(HTML) 25 Page - Texas Instruments

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100 ...More

数据表下载