| 数据搜索系统,热门电子元器件搜索 |
|
VSC8540RT 数据表(PDF) 30 Page - Microchip Technology |
|
|
|||||||||||||||||||||||||||||
VSC8540RT 数据表(HTML) 30 Page - Microchip Technology |
|
30 / 87 page ![]() VSC8540RT DS60001603E-page 30 2022 Microchip Technology Inc. and its subsidiaries 5.11.2 BASIC SERIAL LED MODE The VSC8540RT device can be configured so that access to all its LED signals is available through two pins. This option is enabled by setting LED0 to serial LED mode in register 29, bits 3:0 to 0xD. When serial LED mode is enabled, the LED0 pin becomes the serial data pin, and the LED1 pin becomes the serial clock pin. The serial LED mode clocks the LED status bits on the rising edge of the serial clock. The LED behavior settings can also be used in serial LED mode. The LED combine and LED blink or pulse-stretch set- ting of LED0 is used to control the behavior of each bit of the serial LED stream. To configure LED behavior, set device register 30. The following table shows the serial output bitstream of each LED signal. 5 Reserved Reserved. 6 Link10/100/Activity 1: No link in 10BASE-T or 100BASE-TX. 0: Valid 10BASE-T or 100BASE-TX link. Blink or pulse-stretch = Valid 10BASE-T or 100BASE-TX link with activity present. 7 Reserved Reserved. 8 Duplex/Collision 1: Link established in half-duplex mode, or no link established. 0: Link established in full-duplex mode. Blink or pulse-stretch = Link established in half-duplex mode but collisions are pres- ent. 9 Collision 1: No collision detected. Blink or pulse-stretch = Collision detected. 10 Activity 1: No activity present. Blink or pulse-stretch = Activity present (becomes TX activity present when register bit 30.14 is set to 1). 11 Reserved Reserved. 12 Autonegotiation Fault 1: No auto-negotiation fault present. 0: Auto-negotiation fault occurred. 13 Serial Mode Serial stream. See Section 5.11.2, "Basic Serial LED Mode". Only relevant on PHY port 0. Reserved in others. 14 Force LED Off 1: De-asserts the LED. 15 Force LED On 0: Asserts the LED1. 1. Setting this mode suppresses LED blinking after reset. TABLE 5-15: LED SERIAL BITSTREAM ORDER Output Link/activity 1 Reserved 2 Link100/activity 3 Link10/activity 4 Reserved 5 Duplex/collision 6 Collision 7 Activity 8 Reserved 9 Tx activity 10 Rx activity 11 Autonegotiation fault 12 TABLE 5-14: LED MODE AND FUNCTION SUMMARY (CONTINUED) Mode Function Name LED State and Description |
|
链接网址 |
| ALLDATASHEET是否为您带来帮助? [ DONATE ] |
关于 Alldatasheet | 广告服务 | 联系我们 | 隐私政策 | 数据表链接 | 链接交换 | 制造商名单 All Rights Reserved©Alldatasheet.com |
| Russian : Alldatasheetru.com | Korean : Alldatasheet.co.kr | Spanish : Alldatasheet.es | French : Alldatasheet.fr | Italian : Alldatasheetit.com Portuguese : Alldatasheetpt.com | Polish : Alldatasheet.pl | Vietnamese : Alldatasheet.vn Indian : Alldatasheet.in | Mexican : Alldatasheet.com.mx | British : Alldatasheet.co.uk | New Zealand : Alldatasheet.co.nz |
|
Family Site : ic2ic.com |
icmetro.com |