 |
数据搜索系统，热门电子元器件搜索 |
|
|
数据搜索系统，热门电子元器件搜索 |
|
ADE9178 数据表(PDF) 1 Page - Analog Devices |
|
|
|||||||||||||||||||||||||||||
ADE9178 数据表(HTML) 1 Page - Analog Devices |
|
|
1 / 122 page  Data Sheet ADE9178 Energy Management DSP with PEN Fault Detection 19-101907; Rev A; 3/25 DOCUMENT FEEDBACK TECHNICAL SUPPORT Information furnished by Analog Devices is believed to be accurate and reliable "as is". However, no responsibility is assumed by Analog Devices for its use, nor for any infringements of patents or other rights of third parties that may result from its use. Specifications subject to change without notice. No license is granted by implication or otherwise under any patent or patent rights of Analog Devices. Trademarks and registered trademarks are the property of their respective owners.All Analog Devices products contained herein are subject to release and availability. FEATURES ► Metrology chip for use with any combination of the following AFEs ► ADE9113 (3-channel, isolated, Σ-Δ ADC) ► ADE9112 (2-channel, isolated, Σ-Δ ADC) ► ADE9103 (3-channel, non-isolated, Σ-Δ ADC) ► Can support up to four ADE9113/ADE9112/ADE9103 daisy- chained ADCs through 4-wire SPI ► Supports up to a total of 12 ADC channels of data ► 4-wire SPI for Host MCU communications up to 25 MHz ► Total active energy calculation ► Class C accuracy (0.5%), supports the following ► MID 2014/32/EU Annex V ► EN 50470-1:2006 ► EN 50470-3:2006 ► EN 50470-3:2022 ► IEC 62052-11:2020 ► IEC 62053-21:2020 ► OIML G 22:2022 ► NIST Handbook 44:2023 ► Total apparent energy calculation using filtered RMS ► Energy accumulation, import and export for reverse power/vehi- cle to grid (V2G) applications ► Basic power quality features ► Short-duration undervoltage or overvoltage (dip/swell) detec- tion ► Short-duration undercurrent or overcurrent (dip/swell) detec- tion ► Line frequency calculation with 10 mHz accuracy ► Angles between phase voltages and currents ► Power-factor calculation ► Configurable phase, gain and offset calibration registers for all ADC channels ► Two configurable calibration frequency (CF) pulse outputs ► Configurable: no load detection ► Phase-sequence detection ► RMS on full cycle, half cycle and filtered RMS on all ADC channels ► Supported frequency range: 45 Hz to 65 Hz ► Four user-programmable interrupt outputs (IRQs) ► PEN open fault detection (BS 7671:2018 Amendment 1:2020) ► Waveform streaming through UART transmit pin ► Datapath multiplexing to allow any ADC data to be used for any data processing path ► Temperature range: −40°C to +105°C ► Available in 5 mm × 5 mm, 40-lead LFCSP package APPLICATIONS ► Electric vehicle supply equipment ► Shunt-based polyphase meters ► Solar inverters ► Energy and power monitoring GENERAL DESCRIPTION The ADE9178 is a metrology digital signal processor (DSP) for use with a combination of ADE9113/ADE9112/ADE9103 sigma delta an- alog-to-digital converters (ADCs). The ADE9178 is a high accuracy, 3-phase electrical energy measurement IC primarily for the electric vehicle supply equipment (EVSE) market with serial peripheral interface (SPI) and two flexible pulse outputs. The ADE9178 can in- terface with up to four daisy-chained ADE9113/ADE9112/ADE9103 devices through SPI protocol. The ADE9178 incorporates all the signal processing required to perform total active energy, apparent energy measurements, and root mean square (RMS) calculations. A fixed function DSP executes this signal processing. The ADE9178 is well-suited for the EVSE market due to its broad feature set such as protective earth and neutral (PEN) open fault detection without the need for any additional hardware, overcurrent, and overvoltage detection using RMS of half cycle/one cycle and vehicle to grid/home (V2X) capabilities. The ADE9178 measures active and apparent energy in various 3-phase configurations, such as wye or delta services, with both three and four wires, single phase, and split phase while supporting both 50 Hz and 60 Hz line frequencies. The ADE9178 provides gain, offset, and phase calibration features for each ADC channel. The CF1 and CF2 logic outputs provide power information that is proportional to the measured accumulated energy. The ADE9178 incorporates some basic power quality measurement features, such as short-duration undervoltage/undercurrent or over- voltage/overcurrent detection, line voltage period measurements, and angles between phase voltages and currents. A Host microcon- troller unit (MCU) can be used to communicate with the ADE9178 through 4-wire SPI. Waveform streaming can be accessed by the Host MCU through the WAVEFORM_TX pin of the ADE9178. The ADE9178 also has four user-programmable interrupt pins, IRQ0, IRQ1, IRQ2, and IRQ3, to indicate that an enabled interrupt event has occurred. The ADE9178 is available in a 40-lead, LFCSP package. For more details on how to setup the ADE9178 in an EVSE application, refer to the application note Using ADE9178 for EV Charger Metrology Solution. |
类似零件编号 - ADE9178 |
|
类似说明 - ADE9178 |
|
|
链接网址 |
| ALLDATASHEET是否为您带来帮助? [ DONATE ] |
关于 Alldatasheet | 广告服务 | 联系我们 | 隐私政策 | 数据表链接 | 链接交换 | 制造商名单 All Rights Reserved©Alldatasheet.com |
| Russian : Alldatasheetru.com | Korean : Alldatasheet.co.kr | Spanish : Alldatasheet.es | French : Alldatasheet.fr | Italian : Alldatasheetit.com Portuguese : Alldatasheetpt.com | Polish : Alldatasheet.pl | Vietnamese : Alldatasheet.vn Indian : Alldatasheet.in | Mexican : Alldatasheet.com.mx | British : Alldatasheet.co.uk | New Zealand : Alldatasheet.co.nz |
|
Family Site : ic2ic.com |
icmetro.com |
Chinese ▼
English
Chinese
German
Japanese
Russian
Korean
Spanish
French
Italian
Portuguese
Polish
Vietnamese
Indian
Mexican
British
New Zealand
