CY8CKIT-059 datasheet(50/140 Pages) INFINEON

50 / 140 page

Document Number: 001-84932 Rev. *N

Page 49 of 139

PSoC® 5LP: CY8C58LP Family

Datasheet

7.7 Timers, Counters, and PWMs

The Timer/Counter/PWM peripheral is a 16-bit dedicated

peripheral providing three of the most common embedded

peripheral features. As almost all embedded systems use some

combination of timers, counters, and PWMs. Four of them have

been included on this PSoC device family. Additional and more

advanced functionality timers, counters, and PWMs can also be

instantiated in Universal Digital Blocks (UDBs) as required.

PSoC Creator allows you to choose the timer, counter, and PWM

features that you need. The tool set utilizes the most optimal

resources available.

The Timer/Counter/PWM peripheral can select from multiple

clock sources, with input and output signals connected through

the DSI routing. DSI routing allows input and output connections

to any device pin and any internal digital signal accessible

through the DSI. Each of the four instances has a compare

output, terminal count output (optional complementary compare

output), and programmable interrupt request line. The

Timer/Counter/PWMs are configurable as free running, one

shot, or Enable input controlled. The peripheral has timer reset

and capture inputs, and a kill input for control of the comparator

outputs. The peripheral supports full 16-bit capture.

Timer/Counter/PWM features include:



16-bit timer/counter/PWM (down count only)



Selectable clock source



PWM comparator (configurable for LT, LTE, EQ, GTE, GT)



Period reload on start, reset, and terminal count



Interrupt on terminal count, compare true, or capture



Dynamic counter reads



Timer capture mode



Count while enable signal is asserted mode



Free run mode



One-shot mode (stop at end of period)



Complementary PWM outputs with deadband



PWM output kill

Figure 7-17. Timer/Counter/PWM

7.8 I2C

PSoC includes a single fixed-function I2C peripheral. Additional

I2C interfaces can be instantiated using Universal Digital Blocks

(UDBs) in PSoC Creator, as required.

The I2C peripheral provides a synchronous two-wire interface

designed to interface the PSoC device with a two-wire I2C serial

communication bus. It is compatible[13] with I2C Standard-mode,

Fast-mode, and Fast-mode Plus devices as defined in the NXP

I2C-bus specification and user manual (UM10204). The I2C bus

I/O may be implemented with GPIO or SIO in open-drain modes.

To eliminate the need for excessive CPU intervention and

overhead, I2C specific support is provided for status detection

and generation of framing bits. I2C operates as a slave, a master,

or multimaster (Slave and Master)[13]. In slave mode, the unit

always listens for a start condition to begin sending or receiving

data. Master mode supplies the ability to generate the Start and

Stop conditions and initiate transactions. Multimaster mode

provides clock synchronization and arbitration to allow multiple

masters on the same bus. If Master mode is enabled and Slave

mode is not enabled, the block does not generate interrupts on

externally generated Start conditions. I2C interfaces through the

DSI routing and allows direct connections to any GPIO or SIO

pins.

I2C provides hardware address detect of a 7-bit address without

CPU intervention. Additionally the device can wake from low

power modes on a 7-bit hardware address match. If wakeup

functionality is required, I2C pin connections are limited to one of

two specific pairs of SIO pins. See descriptions of SCL and SDA

pins in Pin Descriptions on page 12.

I2C features include:



Slave and master, transmitter, and receiver operation



Byte processing for low CPU overhead



Interrupt or polling CPU interface



Support for bus speeds up to 1 Mbps



7 or 10-bit addressing (10-bit addressing requires firmware

support)



SMBus operation (through firmware support - SMBus

supported in hardware in UDBs)



7-bit hardware address compare



Wake from low power modes on address match



Glitch filtering (active and alternate-active modes only)

Data transfers follow the format shown in Figure 7-18. After the

START condition (S), a slave address is sent. This address is 7

bits long followed by an eighth bit which is a data direction bit

(R/W) - a 'zero' indicates a transmission (WRITE), a 'one'

indicates a request for data (READ). A data transfer is always

terminated by a STOP condition (P) generated by the master.

Timer / Counter /

PWM 16-bit

Clock

Reset

Enable

Capture

Kill

IRQ

Compare

TC / Compare!

Notes

12. The I2C peripheral is non-compliant with the NXP I2C specification in the following areas: analog glitch filter, I/O VOL/IOL, I/O hysteresis. The I2C Block has a digital

glitch filter (not available in sleep mode). The Fast-mode minimum fall-time specification can be met by setting the I/Os to slow speed mode. See the I/O Electrical

Specifications in Inputs and Outputs on page 76 for details.

13. Fixed-block I2C does not support undefined bus conditions, nor does it support Repeated Start in Slave mode. These conditions should be avoided, or the UDB-based

I2C component should be used instead.

CY8CKIT-059 数据表(PDF) 50 Page - Infineon Technologies AG

CY8CKIT-059 数据表(HTML) 50 Page - Infineon Technologies AG

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100 ...More

数据表下载