CY8CKIT-059 datasheet(59/140 Pages) INFINEON

59 / 140 page

Document Number: 001-84932 Rev. *N

Page 58 of 139

PSoC® 5LP: CY8C58LP Family

Datasheet

Figure 8-9. PGA Resistor Settings

The PGA is used in applications where the input signal may not

be large enough to achieve the desired resolution in the ADC, or

dynamic range of another SC/CT block such as a mixer. The gain

is adjustable at runtime, including changing the gain of the PGA

prior to each ADC sample.

8.6.4 TIA

The Transimpedance Amplifier (TIA) converts an internal or

external current to an output voltage. The TIA uses an internal

feedback resistor in a continuous time configuration to convert

input current to output voltage.For an input current Iin, the output

voltage is VREF - Iin x Rfb, where VREF is the value placed on the

non inverting input. The feedback resistor Rfb is programmable

between 20 K

Ω and 1 MΩ through a configuration register.

Table 8-4 shows the possible values of Rfb and associated

configuration settings.

Figure 8-10. Continuous Time TIA Schematic

The TIA configuration is used for applications where an external

sensor's output is current as a function of some type of stimulus

such as temperature, light, magnetic flux etc. In a common

application, the voltage DAC output can be connected to the

VREF TIA input to allow calibration of the external sensor bias

current by adjusting the voltage DAC output voltage.

8.7 LCD Direct Drive

The PSoC Liquid Crystal Display (LCD) driver system is a highly

configurable peripheral designed to allow PSoC to directly drive

a broad range of LCD glass. All voltages are generated on chip,

eliminating the need for external components. With a high

multiplex ratio of up to 1/16, the CY8C58LP family LCD driver

system can drive a maximum of 736 segments. The PSoC LCD

driver module was also designed with the conservative power

budget of portable devices in mind, enabling different LCD drive

modes and power down modes to conserve power.

PSoC Creator provides an LCD segment drive component. The

component wizard provides easy and flexible configuration of

LCD resources. You can specify pins for segments and

commons along with other options. The software configures the

device to meet the required specifications. This is possible

because of the programmability inherent to PSoC devices.

Key features of the PSoC LCD segment system are:



LCD panel direct driving



Type A (standard) and Type B (low power) waveform support



Wide operating voltage range support (2 V to 5 V) for LCD

panels



Static, 1/2, 1/3, 1/4, 1/5 bias voltage levels



Internal bias voltage generation through internal resistor ladder



Up to 62 total common and segment outputs



Up to 1/16 multiplex for a maximum of 16 backplane/common

outputs



Up to 62 front plane/segment outputs for direct drive



Drives up to 736 total segments (16 backplane x 46 front plane)



Up to 64 levels of software controlled contrast



Ability to move display data from memory buffer to LCD driver

through DMA (without CPU intervention)



Adjustable LCD refresh rate from 10 Hz to 150 Hz



Ability to invert LCD display for negative image



Three LCD driver drive modes, allowing power optimization

Figure 8-11. LCD System

Table 8-3. Bandwidth

Gain

Bandwidth

16.0 MHz

340 kHz

220 kHz

215 kHz

Table 8-4. Feedback Resistor Settings

Configuration Word

Nominal Rfb (KΩ)

000b

001b

010b

011b

100b

120

101b

250

110b

500

111b

1000

20 k to 980 k

20 k or 40 k

Vin

Vref

Vin

Vref

Vout

Iin

R fb

LCD Driver

Block

UDB

DMA

Display

RAM

LCD

DAC

Global

Clock

PHUB

CY8CKIT-059 数据表(PDF) 59 Page - Infineon Technologies AG

CY8CKIT-059 数据表(HTML) 59 Page - Infineon Technologies AG

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100 ...More

数据表下载