PC87309VLJ datasheet(97/192 Pages) NSC

97 / 192 page

Parallel Port (Logical Device 1)

www.national.com

FIGURE 4-6. ECP (Backward) Read Cycle

Notes:

1. FIFO-full condition is checked before every expanded

byte push.

2. Switching from modes 010 or 011 to other modes re-

moves pending DMA requests and aborts pending RLE

expansion.

3. FIFO pushes and pops are neither synchronized nor

linked at the hardware level. The FIFO will not delay

these operations, even if performed concurrently. Care

must be taken by the programmer to utilize the empty

and full FIFO status bits to avoid corrupting PD7-0 or

D7-0 while a previous FIFO port access not complete.

4. In the forward direction, the empty bit is updated when

the ECP cycle is completed, not when the last byte is

popped from the FIFO (valid cleared on cycle end).

5. The one-bit command/data tag is used only in the for-

ward direction.

4.6.3

Automatic Address and Data Transfers

(Mode 100)

Automatic address and data transfer (EPP cycles generat-

ed by hardware) is supported in mode 100. Fast transfers

are achieved by automatically generating the address and

data strobes.

In this mode, the FIFO is reset (empty) and is not functional,

the DMA and RLE are idle.

The direction of the automatic data transfers is determined

by the RD and WR signals. The direction of software data

transfer can be forward or backward, depending on bit 5 of

the DCR. Bit 5 of the DCR determines the default direction

of the data transfers only when there is no on-going EPP cy-

cles.

In EPP mode 100, registers DATAR, DSR and DCR are

used instead of DTR, STR and CTR respectively.

Some differences are caused by the registers. Reading DA-

TAR returns pins values instead of register value returned

when reading DTR. Reading DSR returns register value in-

stead of pins values returned when reading STR. Writing to

the DATAR during an on-going EPP 1.9 forward cycle (i.e.

- when bit 7 of DSR is 1) causes the new data to appear im-

mediately on PD7-0, instead of waiting for BUSY to become

low to switch PD7-0 to the new data when writing to the

DTR.

In addition, the bit 4 of the DCR functions differently relative

to bit 4 of the CTR (IRQ float).

4.6.4

FIFO Test Access (Mode 110)

Mode 110 is for testing the FIFO in PIO and DMA cycles.

Both read and write operations (pop and push) are support-

ed, regardless of the direction bit.

In the forward direction PD7-0 are driven, but the data is un-

defined. This mode can be used to measure the system-

ECP cycle throughput, usually with DMA cycles. This mode

can also be used to check the FIFO depth and its interrupt

threshold, usually with PIO cycles.

4.6.5

Configuration Registers Access (Mode 111)

The two configuration registers, CNFGA and CNFGB, are

accessible only in this mode.

4.6.6

Interrupt Generation

An interrupt is generated when any of the events described

in this section occurs. Interrupt events 2, 3 and 4 are level

events. They are shaped as interrupt pulses, and are

masked (inactive) when the ECP clock is frozen.

Event 1

Bit 2 of ECR is 0, bit 3 of ECR is 1 and TC is asserted

during ECP DMA cycle. Interrupt event 1 is a pulse

event.

Event 2

Bit 2 of ECR is 0, bit 3 of ECR is 0, bit 5 of DCR is 0 and

there are eight or more bytes free in the FIFO.

This event includes the case when bit 2 of ECR is

cleared to 0 and there are already eight or more bytes

free in the FIFO (modes 010, 011 and 110 only).

Event 3

Bit 2 of ECR is 0, bit 3 of ECR is 0, bit 5 of DCR is 1 and

there are eight or more bytes to be read from the FIFO.

This event includes the case when bit 2 of ECR is

cleared to 0 and there are already eight or more bytes

to be read from the FIFO (modes 011 and 110 only).

Event 4

Bit 4 of ECR is 0 and ERR is asserted (high to low edge)

or ERR is asserted when bit 4 of ECR is modified from

1 to 0.

This event may be lost when the ECP clock is frozen.

Event 5

When bit 4 of DCR is 1 and ACK is deasserted (low-to-

high edge).

This event behaves as in the normal SPP mode, i.e., the

IRQ signal follows the ACK signal transition.

PD7-0

BUSY

AFD

ACK

PC87309VLJ 数据表(PDF) 97 Page - National Semiconductor (TI)

PC87309VLJ 数据表(HTML) 97 Page - National Semiconductor (TI)

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100 ...More

数据表下载