LSM6DST datasheet(109/180 Pages) STMICROELECTRONICS

109 / 180 page

DocID033525 Rev 2

109/180

LSM6DST

180

9.61

UI_CTRL1_OIS (70h)

OIS configuration register. The primary interface can write this register when the

OIS_CTRL_FROM_UI bit in the FUNC_CFG_ACCESS (01h) register is equal to 1 (Primary

IF Full control mode); this register is read-only when the OIS_CTRL_FROM_UI bit is equal

to 0 (SPI2 Full control mode) and shows the content of the SPI2_CTRL1_OIS (70h) register.

Table 167. UI_CTRL1_OIS register description

DEN mode selection can be done using the LVL1_OIS bit of register UI_CTRL1_OIS (70h)

and the LVL2_OIS bit of register UI_INT_OIS (6Fh).

DEN mode on the OIS path is active in the gyroscope only.

Table 166. UI_CTRL1_OIS register

0(1)

1. This bit must be set to '0' for the correct operation of the device.

LVL1_OIS

SIM_OIS

Mode4_

FS1_G_

OIS

FS0_G_

OIS

FS_125_

OIS

OIS_EN_

SPI2

LVL1_OIS

Enables level-sensitive trigger mode on OIS chain. Default value: 0

SIM_OIS

SPI2 3- or 4-wire interface. Default value: 0

(0: 4-wire SPI2;

1: 3-wire SPI2)

Mode4_EN

Enables accelerometer OIS chain. When the OIS_CTRL_FROM_UI bit in the

FUNC_CFG_ACCESS (01h) register is equal to 1 (Primary IF Full control mode

enabled), the accelerometer OIS outputs are available through the primary interface

in registers UI_OUTX_L_A_OIS (50h) and UI_OUTX_H_A_OIS (51h) through

UI_OUTZ_L_A_OIS (54h) and UI_OUTZ_H_A_OIS (55h) and

UI_STATUS_REG_OIS (49h).

Note: OIS_EN_SPI2 must be enabled (i.e. set to ‘1’) to enable also XL OIS chain.

FS[1:0]_G_

OIS

Selects gyroscope OIS chain full-scale

(00: ±250 dps;

01: ±500 dps;

10: ±1000 dps;

11: ±2000 dps)

FS_125_OIS

Selects gyroscope OIS chain full-scale ±125 dps

(0: FS selected through bits FS[1:0]_OIS_G;

1: ±125 dps)

OIS_EN_SPI2

Enables OIS chain data processing for gyro in Mode 3 and Mode 4 (mode4_en = 1)

and accelerometer data in and Mode 4 (mode4_en = 1).

When the OIS_CTRL_FROM_UI bit in FUNC_CFG_ACCESS (01h) register is

equal to 1 (Primary IF Full control mode enabled), the gyroscope OIS outputs are

available through the primary interface in registers UI_OUTX_L_G_OIS (4Ah) and

UI_OUTX_H_G_OIS (4Bh) through UI_OUTZ_L_G_OIS (4Eh) and

UI_OUTZ_H_G_OIS (4Fh) and UI_STATUS_REG_OIS (49h), and LPF1 is

dedicated to this chain.

Table 168. DEN mode selection

LVL1_OIS, LVL2_OIS

DEN mode

Level-sensitive trigger mode is selected

Level-sensitive latched mode is selected

LSM6DST 数据表(PDF) 109 Page - STMicroelectronics

LSM6DST 数据表(HTML) 109 Page - STMicroelectronics

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100 ...More

数据表下载