IA188EM-PQF100I-R datasheet(20/133 Pages) INNOVASIC

20 / 133 page

IA186EM/IA188EM

Data Sheet

8/16-BIT Microcontrollers

As of Production Version -03

The value of the LMCS register is undefined at reset except DA, which is set to 0.

5 4 3

UB2 – UB0

DA PSE 1 1 1 R2 R1-R0

Reserved [15] (bit 15) – Set to 0

UB [2:0] (bits 14 – 12) - Upper Boundary. These bits define the upper boundary of memory accessed

by the lcs_n chip select. The following table gives the possible configurations of block size (max

512Kbytes).

LMCS Block Size Programming Values

Memory Block

Size

Ending

Address

UB2 – UB0

64K

0FFFFh

000b

128K

1FFFFh

001b

256K

3FFFFh

011b

512K

7FFFFh

111b

Reserved [11:8] (bits 11-8) - Set to 1.

DA (bit 7) Disable Address - When set to 0, the address is driven onto the address bus (ad15 – ad0)

during the address phase of a bus cycle. If DA is set to 1, the address bus is disabled, providing some

measure of power saving. This bit is set to 0 at reset.

If BHE_n/ADEN_n is held at 0 during the rising edge of res_n, then the address bus is always driven,

independent of the setting of DA.

PSE (bit 6) PSRAM Mode Enable – PSRAM support for the lcs_n chip select memory space is enabled

when the PSE is set to 1. The EDRAM, MDRAM, and CDRAM refresh control unit registers must be

configured for auto refresh before PSRAM support is enabled. Setting the enable bit (EN) in the

enable RCU register (EDRAM, offset e4h) configures the mcs3_n/rfsh_n as rfsh_n.

Reserved (bits 5-3) – Set to 1.

R2 (bit 2) - Ready Mode. When this bit is set to 0, an external ready is required. When set to 1, the

external ready is ignored. In either case, however, the value of the R1 - R0 bits determine the number

of wait states inserted.

R [1:0] (bits R1-R0) - Wait-State Value. The number of wait states inserted into an access to the

LCS_n memory area is determined by the value of these bits. This number ranges from 0 to 3 (R1 – R0

= 00b to 11b)

UMCS (0a0h) - Upper Memory Chip Select Register configures the Upper Memory Chip Select pin,

which is used for the top of memory. On reset, the first fetch takes place at memory location FFFF0h and

thus this area of memory is usually used for instruction memory. With this in mind, UCS_n defaults to an

3737 Princeton NE, Ste 130 • Albuquerque, NM 87107 • Tel 505.883.5263 • Fax 505.883.5477 • www.Innovasic.com

IA188EM-PQF100I-R 数据表(PDF) 20 Page - InnovASIC, Inc

IA188EM-PQF100I-R 数据表(HTML) 20 Page - InnovASIC, Inc

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100 ...More

数据表下载