DSP56303 datasheet(219/292 Pages) FREESCALE

219 / 292 page

Triple Timer Module Programming Model

DSP56303 User’s Manual, Rev. 2

Freescale Semiconductor

9-27

2TCIE

Timer Compare Interrupt Enable

Enables/disables the timer compare interrupts. When set, TCIE enables the

compare interrupts. In the timer, pulse width modulation (PWM), or watchdog

modes, a compare interrupt is generated after the counter value matches the

value of the TCPR. The counter starts counting up from the number loaded

from the TLR and if the TCPR value is M, an interrupt occurs after (M – N + 1)

events, where N is the value of TLR. When cleared, the TCSR[TCIE] bit

disables the compare interrupts.

1TOIE

Timer Overflow Interrupt Enable

Enables timer overflow interrupts. When set, TOIE enables overflow interrupt

generation. The timer counter can hold a maximum value of $FFFFFF. When

the counter value is at the maximum value and a new event causes the

counter to be incremented to $000000, the timer generates an overflow

interrupt. When cleared, the TOIE bit disables overflow interrupt generation.

0TE

Timer Enable

Enables/disables the timer. When set, TE enables the timer and clears the

timer counter. The counter starts counting according to the mode selected by

the timer control (TC[3–0]) bit values. When clear, TE bit disables the timer.

Note:

When all three timers are disabled and the signals are not in GPIO

mode, all three TIO signals are tri-stated. To prevent undesired

spikes on the TIO signals when you switch from tri-state into active

state, these signals should be tied to the high or low signal state by

pull-up or pull-down resistors.

Table 9-4. Inverter (INV) Bit Operation

Mode

TIO Programmed as Input

TIO Programmed as Output

INV = 0

INV = 1

INV = 0

INV = 1

GPIO signal on the TIO signal

read directly.

GPIO signal on the TIO signal

inverted.

Bit written to GPIO

put on TIO signal

directly.

Bit written to GPIO

inverted and put on TIO

signal.

Counter is incremented on the

rising edge of the signal from

the TIO signal.

Counter is incremented on

the falling edge of the signal

from the TIO signal.

——

Counter is incremented on the

rising edge of the signal from

the TIO signal.

Counter is incremented on

the falling edge of the signal

from the TIO signal.

Initial output put on

TIO signal directly.

Initial output inverted

and put on TIO signal.

Counter is incremented on the

rising edge of the signal from

the TIO signal.

Counter is incremented on

the falling edge of the signal

from the TIO signal.

——

Width of the high input pulse is

measured.

Width of the low input pulse is

measured.

——

Period is measured between

the rising edges of the input

signal.

Period is measured between

the falling edges of the input

signal.

——

Table 9-3. Timer Control/Status Register (TCSR) Bit Definitions (Continued)

Bit Number

Bit Name

Reset Value

Description

DSP56303 数据表(PDF) 219 Page - Freescale Semiconductor, Inc

DSP56303 数据表(HTML) 219 Page - Freescale Semiconductor, Inc

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100 ...More

数据表下载

链接网址

DSP56303 数据表(PDF) 219 Page - Freescale Semiconductor, Inc

DSP56303 数据表(HTML) 219 Page - Freescale Semiconductor, Inc

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100 ...More

数据表 下载

链接网址

数据表下载