AM79C971VCW datasheet(35/265 Pages) AMD

35 / 265 page

Am79C971

If the host is not yet ready when the Am79C971 control-

ler asserts TRDY, the device will wait for the host to as-

sert IRDY. When the host asserts IRDY and FRAME is

still asserted, the Am79C971controller will finish the

first data phase by deasserting TRDY one clock later.

At the same time, it will assert STOP to signal a discon-

nect to the host. STOP will stay asserted until the host

removes FRAME. See Figure 8.

Figure 8.

Disconnect Of Slave Burst Transfer -

Host Inserts Wait States

Parity Error Response

When the Am79C971controller is not the current bus

master, it samples the AD[31:0], C/BE[3:0], and the

PAR lines during the address phase of any PCI com-

mand for a parity error. When it detects an address par-

ity error, the controller sets PERR (PCI Status register,

bit 15) to 1. When reporting of that error is enabled by

setting SERREN (PCI Command register, bit 8) and

PERREN (PCI Command register, bit 6) to 1, the

Am79C971controller also drives the SERR signal low

for one clock cycle and sets SERR (PCI Status register,

bit 14) to 1. The assertion of SERR follows the address

phase by two clock cycles. The Am79C971controller

will not assert DEVSEL for a PCI transaction that has

an address parity error when PERREN and SERREN

are set to 1. See Figure 9.

Figure 9.

Address Parity Error Response

During the data phase of an I/O write, memory-mapped

I/O write, or configuration write command that selects

the Am79C971controller as target, the device samples

the AD[31:0] and C/BE[3:0] lines for parity on the clock

edge, and data is transferred as indicated by the asser-

tion of IRDY and TRDY. PAR is sampled in the following

clock cycle. If a parity error is detected and reporting of

that error is enabled by setting PERREN (PCI Com-

mand register, bit 6) to 1, PERR is asserted one clock

later. The parity error will always set PERR (PCI Status

to 0. The Am79C971controller will finish a transaction

that has a data parity error in the normal way by assert-

ing TRDY. The corrupted data will be written to the ad-

dressed location.

Figure 10 shows a transaction that suffered a parity

error at the time data was transferred (clock 7, IRDY

and TRDY are both asserted). PERR is driven high at

the beginning of the data phase and then drops low due

to the parity error on clock 9, two clock cycles after the

data was transferred. After PERR s driven low, the

Am79C971controller drives PERR high for one clock

cycle, since PERR is a sustained tri-state signal.

FRAME

CLK

IRDY

TRDY

C/BE

DEVSEL

STOP

PAR

23456

PAR

DATA

1st DATA

20550D-11

FRAME

CLK

SERR

C/BE

DEVSEL

2345

PAR

ADDR

1st DATA

CMD

PAR

20550D-12

AM79C971VCW 数据表(PDF) 35 Page - Advanced Micro Devices

AM79C971VCW 数据表(HTML) 35 Page - Advanced Micro Devices

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100 ...More

数据表下载