TNETV2664FIBZWT datasheet(72/249 Pages) TI1

72 / 249 page

TMS320C6424

SPRS347D – MARCH 2007 – REVISED DECEMBER 2009

www.ti.com

Table 3-4. Non-Fastboot Modes (FASTBOOT = 0)

DEVICE BOOT AND

PLLC1 CLOCK SETTING AT BOOT

CONFIGURATION PINS

C6424 DMP

DSPBOOTADDR

BOOT DESCRIPTION(1)

DEVICE

(Master/Slave)

(DEFAULT)(1)

PLL

CLKDIV1 DOMAIN

BOOTMODE[3:0]

PCIEN

FREQUENCY

MODE(2)

(SYSCLK1 DIVIDER)

(SYSCLK1)

0000

0 or 1

No Boot (Emulation Boot)

Master

Bypass

CLKIN

0x0010 0000

0001

0 or 1

Reserved

–

HPI Boot

Slave

Bypass

CLKIN

0x0010 0000

0010

Reserved

–

0011

0 or 1

Reserved

–

EMIFA ROM Direct Boot

0100

0 or 1

Master

Bypass

CLKIN

0x4200 000

[PLL Bypass Mode]

I2C Boot

0101

0 or 1

Master

Bypass

CLKIN

0x0010 0000

[STANDARD MODE](3)

16-bit SPI Boot

0110

0 or 1

Master

Bypass

CLKIN

0x0010 0000

[McBSP0]

0111

0 or 1

NAND Flash Boot

Master

Bypass

CLKIN

0x0010 0000

UART Boot without

1000

0 or 1

Hardware Flow Control

Master

Bypass

CLKIN

0x0010 0000

[UART0]

1001

0 or 1

Reserved

–

1010

0 or 1

VLYNQ Boot

Slave

Bypass

CLKIN

0x0010 0000

1011

0 or 1

Reserved

–

1100

0 or 1

Reserved

–

1101

0 or 1

Reserved

–

UART Boot with

1110

0 or 1

Hardware Flow Control

Master

Bypass

CLKIN

0x0010 0000

[UART0]

24-bit SPI Boot

1111

0 or 1

Master

Bypass

CLKIN

0x0010 0000

(McBSP0 + GP[97])

(1)

For all boot modes that default to DSPBOOTADDR = 0x0010 0000 (i.e., all boot modes except the EMIFA ROM Direct Boot,

BOOTMODE[3:0] = 0100, FASTBOOT = 0), the bootloader code disables all C64x+ cache (L2, L1P, and L1D) so that upon exit from the

bootloader code, all C64x+ memories are configured as all RAM. If cache use is required, the application code must explicitly enable the

cache. For more information on the bootloader, see the Using the TMS320C642x Bootloader Application Report (literature number

SPRAAK5).

(2)

The PLL MODE for Non-Fastboot Modes is fixed as shown in this table; therefore, the PLLMS[2:0] configuration pins have no effect on

the PLL MODE.

(3)

I2C Boot (BOOTMODE[3:0] = 0101b) is only available if the MXI/CLKIN frequency is between 21 MHz to 30 MHz. I2C Boot is not

available for MXI/CLKIN frequencies less than 21 MHz.

Device Configurations

Submit Documentation Feedback

Product Folder Link(s): TMS320C6424

TNETV2664FIBZWT 数据表(PDF) 72 Page - Texas Instruments

TNETV2664FIBZWT 数据表(HTML) 72 Page - Texas Instruments

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100 ...More

数据表下载

链接网址

TNETV2664FIBZWT 数据表(PDF) 72 Page - Texas Instruments

TNETV2664FIBZWT 数据表(HTML) 72 Page - Texas Instruments

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100 ...More

数据表 下载

链接网址

数据表下载