DSP56303 datasheet(144/292 Pages) FREESCALE

144 / 292 page

DSP56303 User’s Manual, Rev. 2

7-12

Freescale Semiconductor

Enhanced Synchronous Serial Interface (ESSI)

7.4.9 Flags

Two ESSI signals (SC[1–0]) are available for use as serial I/O flags. Their operation is controlled

by the SYN, SCD[1–0], SSC1, and TE[2–1] bits in the CRB/CRA.The control bits OF[1–0] and

status bits IF[1–0] are double-buffered to and from SC[1–0]. Double-buffering the flags keeps

the flags in sync with TX and RX.

The SC[1–0] flags are available in Synchronous mode only. Each flag can be separately

programmed. The SC0 flag is enabled when transmitter 1 is disabled (TE1 = 0). The flag’s

direction is selected by the SCD0 bit. When SCD0 is set, SC0 is configured as output. When

SCD0 is cleared, SC0 is configured as input. Similarly, the SC1 flag is enabled when transmitter 2

is disabled (TE2 = 0), and the SC1 signal is not configured as the transmitter 0 drive-enabled

signal (Bit SSC1 = 0). The direction of SC1 is determined by the SCD1 bit. When SCD1 is set,

SC1

is an output flag. When SCD1 is cleared, SC1 is an input flag.

When programmed as input flags, the value of the SC[1–0] bits is latched at the same time as the

first bit of the received data word is sampled. Once the input is latched, the signal on the input

flag signal (SC0 and SC1) can change without affecting the input flag. The value of SC[1–0] does

not change until the first bit of the next data word is received. When the received data word is

latched by RX, the latched values of SC[1–0] are latched by the SSISR IF[1–0] bits, respectively,

and can be read by software.

When they are programmed as output flags, the value of the SC[1–0] bits is taken from the value

of the OF[1–0] bits. The value of OF[1–0] is latched when the contents of TX transfer to the

transmit shift register. The value on SC[1–0] is stable from the time the first bit of the transmit

data word transmits until the first bit of the next transmit data word transmits. Software can

directly set the OF[1–0] values, allowing the DSP56303 to control data transmission by indirectly

controlling the value of the SC[1–0] flags.

7.5 ESSI Programming Model

The ESSI is composed of the following registers:

Two control registers (CRA, CRB), page 7-13 and page 7-17

One status register (SSISR), page 7-26

One Receive Shift Register, page 7-28

One Receive Data Register (RX), page 7-28

Three Transmit Shift Registers, page 7-28

Three Transmit Data Registers (TX0, TX1, TX2), page 7-28

One special-purpose Time Slot Register (TSR), page 7-31

Two Transmit Slot Mask Registers (TSMA, TSMB), page 7-31

Two Receive Slot Mask Registers (RSMA, RSMB), page 7-32

DSP56303 数据表(PDF) 144 Page - Freescale Semiconductor, Inc

DSP56303 数据表(HTML) 144 Page - Freescale Semiconductor, Inc

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100 ...More

数据表下载