AM79C970 datasheet(49/168 Pages) AMD

49 / 168 page

AMD

P R E L I M I N A R Y

1-916

Am79C970

Polling

If there is no network channel activity and there is no

pre- or post-receive or pre- or post-transmit activity be-

ing performed by the PCnet-PCI controller, then the

PCnet-PCI controller will periodically poll the current re-

ceive and transmit descriptor entries in order to ascer-

tain their ownership. If the DPOLL bit in CSR4 is set,

then the transmit polling function is disabled.

A typical polling operation consists of the following: The

PCnet-PCI controller will use the current receive de-

scriptor address stored internally to vector to the appro-

priate Receive Descriptor Table Entry (RDTE). It will

then use the current transmit descriptor address (stored

internally) to vector to the appropriate Transmit Descrip-

tor Table Entry (TDTE). The accesses will be made in

the following order: RMD1, then RMD0 of the current

RDTE during one bus arbitration, and after that, TMD1,

then TMD0 of the current TDTE during a second bus ar-

bitration. All information collected during polling activity

will be stored internally in the appropriate CSRs. (i.e.

CSR18, CSR19, CSR20, CSR21, CSR40, CSR42,

CSR50, CSR52). UnOWNed descriptor status will be in-

ternally ignored.

A typical receive poll is the product of the following

conditions:

1. PCnet-PCI controller does not possess ownership

of the current RDTE and the poll time has elapsed

and RXON=1 (CSR0, bit 5), or

2. PCnet-PCI controller does not possess ownership

of the next RDTE the poll time has elapsed and

RXON=1.

If RXON=0 the PCnet-PCI controller will never poll

RDTE locations.

The ideal system should always have at least one RDTE

available for the possibility of an unpredictable receive

event. (This condition is not a requirement. If this condi-

tion is not met, it simply means that frames will be

missed by the system because there was no buffer

space available.) But the typical system usually has at

least one or two RDTEs available for the possibility of an

unpredictable receive event. Given that this condition is

satisfied, the current and next RDTE polls are rarely

seen and hence, the typical poll operation simply con-

sists of a check of the status of the current TDTE. When

there is only one RDTE (because the RLEN was set to

ZERO), then there is no “next RDTE” and ownership of

“next RDTE” cannot be checked. If there is at least one

RDTE, the RDTE poll will rarely be seen and the typical

poll operation simply consists of a check of the

current TDTE.

A typical transmit poll is the product of the following

conditions:

1. PCnet-PCI controller does not possess ownership

of the current TDTE and

DPOLL=0 (CSR4, bit 2) and

TXON=1 (CSR0, bit 4) and

the poll time has elapsed, or

2. PCnet-PCI controller does not possess ownership

of the current TDTE and

DPOLL=0 and

TXON=1 and

a frame has just been received, or

3. PCnet-PCI controller does not possess ownership

of the current TDTE and

DPOLL=0 and

TXON=1 and

a frame has just been transmitted.

Setting the TDMD bit of CSR0 will cause the microcode

controller to exit the poll counting code and immediately

perform a polling operation. If RDTE ownership has not

been previously established, then an RDTE poll will be

performed ahead of the TDTE poll. If the microcode is

not executing the poll counting code when the TDMD bit

is set, then the demanded poll of the TDTE will be de-

layed

until

the

microcode

returns

the

poll

counting code.

The user may change the poll time value from the de-

fault of 65,536 clock periods by modifying the value in

the Polling Interval register (CSR47). Note that if a non–

default value is desired, then a strict sequence of setting

the INIT bit in CSR0, waiting for IDONE, then writing to

CSR47, and then setting STRT in CSR0 must be ob-

served, otherwise the default value will not be overwrit-

ten. See the CSR47 section for details.

Transmit Descriptor Table Entry (TDTE)

If, after a TDTE access, the PCnet-PCI controller finds

that the OWN bit of that TDTE is not set, then the PCnet-

PCI controller resumes the poll time count and

reexamines the same TDTE at the next expiration of the

poll time count.

If the OWN bit of the TDTE is set, but Start of Frame

(STP) bit is not set, the PCnet-PCI controller will imme-

diately request the bus in order to reset the OWN bit of

this descriptor. (This condition would normally be found

following a LCOL or RETRY error that occurred in the

middle of a transmit frame chain of buffers.) After reset-

ting the OWN bit of this descriptor, the PCnet-PCI con-

troller will again immediately request the bus in order to

access the next TDTE location in the ring.

AM79C970 数据表(PDF) 49 Page - Advanced Micro Devices

AM79C970 数据表(HTML) 49 Page - Advanced Micro Devices

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100 ...More

数据表下载

链接网址

AM79C970 数据表(PDF) 49 Page - Advanced Micro Devices

AM79C970 数据表(HTML) 49 Page - Advanced Micro Devices

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100 ...More

数据表 下载

链接网址

数据表下载