TNETA1570 datasheet(32/68 Pages) TI1

32 / 68 page

TNETA1570

ATM SEGMENTATION AND REASSEMBLY DEVICE

WITH INTEGRATED 64BIT PCIHOST INTERFACE

SDNS033B − JUNE 1995 − REVISED MAY 1996

POST OFFICE BOX 655303

• DALLAS, TEXAS 75265

POST OFFICE BOX 1443

• HOUSTON, TEXAS 77251−1443

PRINCIPLES OF OPERATION

RDY (bit 31)

This bit indicates whether the buffer is ready for segmentation. The host sets this bit to a one to indicate that

the buffer is ready to be transmitted. The TNETA1570 does not write to this bit.

The RDY bits of the buffers within a packet, which has a cell divided across multiple buffers, is set in a zipper-up

fashion, (i.e. the RDY bit of the last buffer in the chain is set first). If the last cell in the buffer has its beginning

in one buffer and the ending in another, the RDY bit for the first buffer cannot be set before the RDY bit for the

second buffer is set. This propagates down the buffer chain until a cell is completed on an even buffer boundary.

start of packet (SOP) (bit 30)

This bit is set by the host indicating that this is the first buffer of a packet that consists of one or more buffers.

This bit is also set if a packet consists of only a single buffer.

end of packet (EOP) (bit 29)

This bit is set by the host to indicate that this is the last buffer of a packet. If a packet consists of only one buffer,

both the SOP and EOP bits are set. If a packet consists of multiple buffers, the SOP bit is set on the first buffer

and the EOP bit is set on the last buffer.

abort (bit 28)

When this bit is set by the host, the TNETA1570 stops segmentation of the packet and performs EOP processing

immediately. An entry is written into the transmit completion ring indicating that an abort has occurred. When

an abort occurs, the AAL5-length field in the AAL5 trailer of the last cell transmitted is set to zero to indicate that

an abort has occurred.

transmit AAL-packet-type indicator (bits 27 and 26)

These bits are set by the host to indicate the AAL type of the packet being transmitted. Three options are

available for processing a packet for transmission as shown in the following table.

BIT 27

BIT 26

INDICATION

Transparent-AAL packet with PTI bits set to indicate EOP

AAL5

Transparent-AAL packet without PTI bits set to indicate EOP

Invalid

AAL5 processing includes the calculation of the 32-bit CRC and the addition of the pad, control, and length fields.

All buffers associated with an AAL5 packet must have the AAL5-indication bits set. When either of the other two

processing methods is chosen, the TNETA1570 does not perform packet-level processing except for adding

the necessary pad to complete a 48-byte payload. If both bits 27 and 26 are set to zero, the device also sets

the PTI field in the last cell of a packet to a value of 0 x 1 to indicate EOP. If bits 27 and 26 are set to a value

of 10, the PTI field in the last cell of the packet is not modified. This last method can be used to send VC-level

OAM cells, which requires that the PTI value of the cell being transmitted be set to a value of 10x. The

TNETA1570 does not modify the PTI field for these cells.

transmit completion-ring select (bit 25)

This bit is set by the host to indicate whether the TNETA1570 uses the transmit completion ring with or without

interrupt when a buffer completes segmentation. If this bit is set to a one, the TNETA1570 uses the completion

ring with interrupt. If this bit is cleared, the TNETA1570 uses the completion ring without interrupt.

TNETA1570 数据表(PDF) 32 Page - Texas Instruments

TNETA1570 数据表(HTML) 32 Page - Texas Instruments

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68

数据表下载