AM79C971VCW datasheet(170/265 Pages) AMD

170 / 265 page

170

Am79C971

P R E L I M INARY

Table 35.

Interface Pin Assignment

BCR20: Software Style

This register is an alias of the location CSR58. Accesses

to and from this register are equivalent to accesses to

CSR58.

Bit

Name

Description

31-16 RES

Reserved locations. Written as

zeros and read as undefined.

15-11 RES

Reserved locations. Written as

zeros and read as undefined.

APERREN

Advanced Parity Error Handling

Enable. When APERREN is set

to 1, the BPE bits (RMD1 and

TMD1, bit 23) start having a

meaning. BPE will be set in the

descriptor associated with the

buffer that was accessed when a

data parity error occurred. Note

that since the advanced parity er-

ror handling uses an additional bit

in the descriptor, SWSTYLE (bits

7-0 of this register) must be set to

2 or 3 to program the Am79C971

controller to use 32-bit software

structures.

APERREN does not affect the re-

porting of address parity errors or

data parity errors that occur when

the Am79C971 controller is the

target of the transfer.

Read anytime; write accessible

only when either the STOP or the

SPND bit is set. APERREN is

cleared by H_RESET and is not

affected by S_RESET or STOP.

RES

Reserved locations. Written as

zeros; read as undefined.

SSIZE32

Software Size 32 bits. When set,

this

bit

indicates

that

the

Am79C971 controller utilizes 32-

bit software structures for the ini-

tialization block and the transmit

and receive descriptor entries.

When cleared, this bit indicates

that the Am79C971 controller uti-

lizes 16-bit software structures for

the initialization block and the

transmit and receive descriptor

entries.

this

mode,

the

Am79C971 controller is back-

wards

compatible

with

the

Am7990 LANCE and Am79C960

PCnet-ISA controllers.

The value of SSIZE32 is deter-

mined by the Am79C971 control-

ler according to the setting of the

Software Style (SWSTYLE, bits

7-0 of this register).

Read

accessible

always.

SSIZE32 is read only; write oper-

ations will be ignored. SSIZE32

will be cleared after H_RESET

(since SWSTYLE defaults to 0)

and is not affected by S_RESET

or STOP.

If SSIZE32 is reset, then bits

IADR[31:24] of CSR2 will be

used to generate values for the

upper 8 bits of the 32-bit address

bus during master accesses initi-

ated by the Am79C971 controller.

This action is required, since the

16-bit software structures speci-

fied by the SSIZE32 = 0 setting

will yield only 24 bits of address

for Am79C971

controller bus

master accesses.

If SSIZE32 is set, then the soft-

ware structures that are common

to the Am79C971 controller and

the host system will supply a full

32 bits for each address pointer

that is needed by the Am79C971

controller for performing master

accesses.

RST Pin

PREAD or Auto

Read in Progress

EEN

EECS

EESK

EEDI

Low

Tri-State

High

Active

High

From ECS

Bit of BCR19

From ESK Bit of

BCR19

From EEDI Bit of

BCR19

High

LED1

LED0

AM79C971VCW 数据表(PDF) 170 Page - Advanced Micro Devices

AM79C971VCW 数据表(HTML) 170 Page - Advanced Micro Devices

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100 ...More

数据表下载

链接网址

AM79C971VCW 数据表(PDF) 170 Page - Advanced Micro Devices

AM79C971VCW 数据表(HTML) 170 Page - Advanced Micro Devices

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100 ...More

数据表 下载

链接网址

数据表下载