ADP1050ACPZ-R7 datasheet(52/93 Pages) AD

52 / 93 page

Data Sheet

ADP1050

PMBus COMMAND DESCRIPTIONS

BASIC PMBus COMMANDS

OPERATION

The OPERATION command is used to turn the unit on and off in conjunction with the input from the CTRL pin. It is also used to set the

output voltage to the upper or lower voltage margin. The unit stays in the commanded operating mode until a subsequent OPERATION

command instructs the device to change to another mode.

Table 13. Register 0x01—OPERATION

Bits

Bit Name/Function

R/W

Description

[7:6]

Enable

R/W

These bits determine the response to the OPERATION command.

Bit 7

Bit 6

Description

Immediate off (no sequencing)

Soft off (power-down based on the programmed TOFF_DELAY command)

Unit on

Reserved

[5:4]

Margin control

R/W

These bits set the voltage margin level.

Bit 5

Bit 4

Description

Off

Margin low

Margin high

Reserved

[3:0]

Reserved

Reserved.

ON_OFF_CONFIG

The ON_OFF_CONFIG command configures the combination of CTRL pin input and serial bus commands needed to turn the unit on and off,

including how the unit responds when power is applied.

Table 14. Register 0x02—ON_OFF_CONFIG

Bits

Bit Name/Function

R/W

Description

[7:5]

Reserved

Reserved.

Power-up control

R/W

Controls how the device responds to the OPERATION command.

0 = the unit powers up whenever power is present.

1 = the unit powers up only when commanded by the CTRL pin and the OPERATION command

(as programmed in Register 0x02, Bits[3:0]).

Command enable

R/W

Controls how the device responds to the OPERATION command.

0 = ignores the OPERATION command.

1 = requires that the OPERATION command be set to the on state to enable the unit (in addition to

the setting of Bit 2).

Pin enable

R/W

Controls how the device responds to the value on the CTRL pin.

0 = ignores the CTRL pin.

1 = requires the CTRL pin to be asserted to enable the unit (in addition to the setting of Bit 3).

CTRL pin polarity

R/W

Sets the polarity for the CTRL pin.

0 = active low.

1 = active high.

Power-down delay

setting

R/W

Action to take at power-down.

0 = uses the TOFF_DELAY value (TOFF_FALL is not supported by the ADP1050) to stop the

transfer of energy to the output.

1 = turns off the output and stops energy transfer to the output as fast as possible.

Rev. A | Page 51 of 92

ADP1050ACPZ-R7 数据表(PDF) 52 Page - Analog Devices

ADP1050ACPZ-R7 数据表(HTML) 52 Page - Analog Devices

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93

数据表下载

链接网址

ADP1050ACPZ-R7 数据表(PDF) 52 Page - Analog Devices

ADP1050ACPZ-R7 数据表(HTML) 52 Page - Analog Devices

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93

数据表 下载

链接网址

数据表下载