数据搜索系统,热门电子元器件搜索
  Chinese  ▼
ALLDATASHEETCN.COM

X  

TNETV1002IDZHK 数据表(PDF) 42 Page - Texas Instruments

部件名 TNETV1002IDZHK
功能描述  Fixed-Point Digital Signal Processor
PDF  102 Pages
Scroll/Zoom Zoom In 100%  Zoom Out
制造商  TI1 [Texas Instruments]
网页  http://www.ti.com
标志 TI1 - Texas Instruments

TNETV1002IDZHK 数据表(HTML) 42 Page - Texas Instruments

Back Button TNETV1002IDZHK Datasheet HTML 38Page - Texas Instruments TNETV1002IDZHK Datasheet HTML 39Page - Texas Instruments TNETV1002IDZHK Datasheet HTML 40Page - Texas Instruments TNETV1002IDZHK Datasheet HTML 41Page - Texas Instruments TNETV1002IDZHK Datasheet HTML 42Page - Texas Instruments TNETV1002IDZHK Datasheet HTML 43Page - Texas Instruments TNETV1002IDZHK Datasheet HTML 44Page - Texas Instruments TNETV1002IDZHK Datasheet HTML 45Page - Texas Instruments TNETV1002IDZHK Datasheet HTML 46Page - Texas Instruments Next Button
Zoom Inzoom in Zoom Outzoom out
 42 / 102 page
background image
MCU Subsystem Functional Overview
32
June 2001 -- Revised December 2002
SPRS180C
4.2.3 MCU SDRAM Memory Interface
The SDRAM memory interface main features are:
It operates with the MCU memory interface (MEMINT) so that SDRAM memories can be used on the
same board with Flash and/or SRAM.
Supports 16- and 32-bit-wide data bus to SDRAM parts
Can address up to 256M bits of SDRAM
Operates at the MCU clock speed (47.5 MHz)
Flexible programming of SDRAM timing parameters
Supports four open SDRAM pages
Minimal burst operations supported. (In 16-bit-wide mode, a burst of two is supported.)
The SDRAM interface must be properly initialized before the SDRAM memory can be used. The following
steps are needed for initializing the SDRAM Interface:
Program SDRAM_REG for data bus size and the number of dummy cycles used after access to slower
memory device.
Program SDRAM parameters in SDRAM_CONFIG, SDRAM_REF_COUNT, and SDRAM_INIT_CONF
Write a ‘1’ in the INIT bit of the SDRAM_CNTL register
Wait until a ‘1’ is read inside the READY bit of the SDRAM_CNTL register before accessing the SDRAM.
NOTE: By writing a ‘1’ in the INIT bit of the SDRAM_CNTL register, the initialization state
machine of the SDRAM interface module will do the following: Wait for the number of cycles
that is programmed in INIT_NOP_MAX_CNT (should be 100 μs or greater). Send the
specified number of refresh commands that have been programmed into the
INIT_REF_MAX_CNT register.
The SDRAM load-mode-register command is used to configure the SDRAM device mode. Parameters used
in the load-mode-register command are based on the values programmed in the SDRAM interface registers.



Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100  ...More


数据表 下载

Go To PDF Page


链接网址



ALLDATASHEET是否为您带来帮助?  [ DONATE ] 

关于 Alldatasheet   |   广告服务   |   联系我们   |   隐私政策   |   数据表链接    |   链接交换   |   制造商名单
All Rights Reserved©Alldatasheet.com


Mirror Sites
English : Alldatasheet.com  |   English : Alldatasheet.net  |   Chinese : Alldatasheetcn.com  |   German : Alldatasheetde.com  |   Japanese : Alldatasheet.jp
Russian : Alldatasheetru.com  |   Korean : Alldatasheet.co.kr  |   Spanish : Alldatasheet.es  |   French : Alldatasheet.fr  |   Italian : Alldatasheetit.com
Portuguese : Alldatasheetpt.com  |   Polish : Alldatasheet.pl  |   Vietnamese : Alldatasheet.vn
Indian : Alldatasheet.in  |   Mexican : Alldatasheet.com.mx  |   British : Alldatasheet.co.uk  |   New Zealand : Alldatasheet.co.nz
Family Site : ic2ic.com  |   icmetro.com