TNETV1002IDZHK datasheet(79/102 Pages) TI1

79 / 102 page

Electrical Specifications

June 2001 -- Revised December 2002

SPRS180C

Low inactive state with delay; the McBSP transmits data one-half cycle ahead of the rising edge of BCLKX

and receives data on the rising edge of BCLKR.

Table 6--22 and Table 6--23 assume testing over recommended operating conditions, CLKSTP = 11b,

CLKXP = 0, and H = 0.5tc(CO) (see Figure 6--20).

NOTE: For all SPI slave modes, CLKG is programmed as 1/2 of the CPU clock by setting

CLKSM = CLKGDV = 1.

Table 6--22. McBSP as SPI Master or Slave Timing Requirements (CLKSTP = 11b and CLKXP = 0)

MASTER

SLAVE

UNIT

MIN

MAX

MIN

MAX

UNIT

tsu(BDRV-BCKXL)

Setup time, BDR valid before BCLKX low

-- 12H

th(BCKXH-BDRV)

Hold time, BDR valid after BCLKX high

12H + 5

tsu(BFXL-BCKXH)

Setup time, BFSX low before BCLKX high

tc(BCKX)

Cycle time, BCLKX

12H

32H

Table 6--23. McBSP as SPI Master or Slave Switching Characteristics (CLKSTP = 11b and CLKXP = 0)

PARAMETER

MASTER†

SLAVE

UNIT

PARAMETER

MIN

MAX

MIN

MAX

UNIT

th(BCKXL-BFXL)

Hold time, BFSX low after BCLKX low‡

T-- 6

T+6

td(BFXL-BCKXH)

Delay time, BFSX low to BCLKX high§

C-- 6

C+ 6

td(BCKXL-BDXV)

Delay time, BCLKX low to BDX valid

-- 3

6H + 5 10H + 14

tdis(BCKXL-BDXHZ)

Disable time, BDX high impedance following last data bit from

BCLKX low

-- 2

6H + 3 10H + 17

td(BFXL-BDXV)

Delay time, BFSX low to BDX valid

C-- 6

C+ 6

4H -- 2

8H + 17

† T = BCLKX period = (1 + CLKGDV) * 2H

C = BCLKX low pulse width = T/2 when CLKGDV is odd or zero and = (CLKGDV/2) * 2H when CLKGDV is even

D = BCLKX high pulse width = T/2 when CLKGDV is odd or zero and = (CLKGDV/2 + 1) * 2H when CLKGDV is even

‡ FSRP = FSXP = 1. As a SPI master, BFSX is inverted to provide active-low slave-enable output. As a slave, the active-low signal input on BFSX

and BFSR is inverted before being used internally.

CLKXM = FSXM = 1, CLKRM = FSRM = 0 for master McBSP

CLKXM = CLKRM = FSXM = FSRM = 0 for slave McBSP

§ BFSX should be low before the rising edge of clock to enable slave devices and then begin a SPI transfer at the rising edge of the master clock

(BCLKX).

Bit 0

Bit(n-1)

(n-2)

(n-3)

(n-4)

Bit 0

Bit(n-1)

(n-2)

(n-3)

(n-4)

BCLKX

BFSX

BDX

BDR

td(BFXL-BCKXH)

tdis(BCKXL-BDXHZ)

td(BCKXL-BDXV)

th(BCKXH-BDRV)

tsu(BDRV-BCKXL)

td(BFXL-BDXV)

th(BCKXL-BFXL)

LSB

MSB

tsu(BFXL-BCKXH)

tc(BCKX)

Figure 6--20. McBSP Timing as SPI Master or Slave: CLKSTP = 11b, CLKXP = 0

TNETV1002IDZHK 数据表(PDF) 79 Page - Texas Instruments

TNETV1002IDZHK 数据表(HTML) 79 Page - Texas Instruments

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100 ...More

数据表下载

链接网址

TNETV1002IDZHK 数据表(PDF) 79 Page - Texas Instruments

TNETV1002IDZHK 数据表(HTML) 79 Page - Texas Instruments

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100 ...More

数据表 下载

链接网址

数据表下载