| 数据搜索系统,热门电子元器件搜索 |
|
ZUSBOPTSC01ZACG 数据表(PDF) 212 Page - Zilog, Inc. |
|
|
|||||||||||||||||||||||||||||
ZUSBOPTSC01ZACG 数据表(HTML) 212 Page - Zilog, Inc. |
|
212 / 282 page ![]() PS022827-1212 P R E L I M I N A R Y Operation Z8 Encore! XP® F082A Series Product Specification 195 When selecting a new clock source, the system clock oscillator failure detection circuitry and the Watchdog Timer oscillator failure circuitry must be disabled. If SOFEN and WOFEN are not disabled prior to a clock switch-over, it is possible to generate an inter- rupt for a failure of either oscillator. The Failure detection circuitry can be enabled any- time after a successful write of OSCSEL in the OSCCTL Register. The internal precision oscillator is enabled by default. If the user code changes to a differ- ent oscillator, it may be appropriate to disable the IPO for power savings. Disabling the IPO does not occur automatically. Clock Failure Detection and Recovery Should an oscillator or timer fail, there are methods of recovery, as this section describes. System Clock Oscillator Failure The Z8F04xA family devices can generate nonmaskable interrupt-like events when the primary oscillator fails. To maintain system function in this situation, the clock failure recovery circuitry automatically forces the Watchdog Timer oscillator to drive the system clock. The Watchdog Timer oscillator must be enabled to allow the recovery. Although this oscillator runs at a much slower speed than the original system clock, the CPU contin- ues to operate, allowing execution of a clock failure vector and software routines that either remedy the oscillator failure or issue a failure alert. This automatic switch-over is not available if the Watchdog Timer is selected as the system clock oscillator. It is also unavailable if the Watchdog Timer oscillator is disabled, though it is not necessary to enable the Watchdog Timer reset function (see the Watchdog Timer chapter on page 93). The primary oscillator failure detection circuitry asserts if the system clock frequency drops below 1kHz ±50%. If an external signal is selected as the system oscillator, it is pos- sible that a very slow but nonfailing clock can generate a failure condition. Under these conditions, do not enable the clock failure circuitry (SOFEN must be deasserted in the OSCCTL Register). Watchdog Timer Failure In the event of a Watchdog Timer oscillator failure, a similar nonmaskable interrupt-like event is issued. This event does not trigger an attendant clock switch-over, but alerts the CPU of the failure. After a Watchdog Timer failure, it is no longer possible to detect a pri- mary oscillator failure. The failure detection circuitry does not function if the Watchdog Timer is used as the system clock oscillator or if the Watchdog Timer oscillator has been disabled. For either of these cases, it is necessary to disable the detection circuitry by deas- serting the WDFEN bit of the OSCCTL Register. The Watchdog Timer oscillator failure detection circuit counts system clocks while look- ing for a Watchdog Timer clock. The logic counts 8004 system clock cycles before deter- mining that a failure has occurred. The system clock rate determines the speed at which |
|
链接网址 |
| ALLDATASHEET是否为您带来帮助? [ DONATE ] |
关于 Alldatasheet | 广告服务 | 联系我们 | 隐私政策 | 数据表链接 | 链接交换 | 制造商名单 All Rights Reserved©Alldatasheet.com |
| Russian : Alldatasheetru.com | Korean : Alldatasheet.co.kr | Spanish : Alldatasheet.es | French : Alldatasheet.fr | Italian : Alldatasheetit.com Portuguese : Alldatasheetpt.com | Polish : Alldatasheet.pl | Vietnamese : Alldatasheet.vn Indian : Alldatasheet.in | Mexican : Alldatasheet.com.mx | British : Alldatasheet.co.uk | New Zealand : Alldatasheet.co.nz |
|
Family Site : ic2ic.com |
icmetro.com |