CS5530 datasheet(71/241 Pages) NSC

71 / 241 page

Revision 4.1

www.national.com

Functional Description (Continued)

F0 Index 8Ah

General Purpose Timer 2 Count Register (R/W)

Reset Value = 00h

7:0

General Purpose Timer 2 Count: This field represents the load value for GP Timer 2. This value can represent either an

8-bit or 16-bit counter (configured in F0 Index 8Bh[5]). It is loaded into the counter when the timer is enabled (F0 Index

83h[1] = 1). Once the timer is enabled and a transition occurs on GPIO7, the timer is re-loaded.

The counter is decremented with each clock of the configured timebase. Upon expiration of the counter, an SMI is gener-

ated and the top level of status is F1BAR+Memory Offset 00h/02h[9] and the second level of status is reported in

F1BAR+Memory Offset 04h/06h[1]).

Once expired, this counter must be re-initialized by either disabling and enabling it, or writing a new count value here.

For GPIO7 to act as the reload for this counter, it must be enabled as such (F0 Index 8Bh[2]) and be configured as an

input (F0 Index 90h[7]).

This counter’s timebase can be configured as 1 msec or 1 sec in F0 Index 8Bh[3].

F0 Index 8Bh

General Purpose Timer 2 Control Register (R/W)

Reset Value = 00h

Re-trigger General Purpose Timer 1 on Secondary Hard Disk Activity: 0 = Disable; 1 = Enable.

Any access to the secondary hard disk drive address range selected in F0 Index 93h[4] reloads GP Timer 1.

VGA Timer Base: Selects timebase for VGA Timer Register (F0 Index 8Eh): 0 = 1 ms; 1 = 32 µs.

General Purpose Timer 2 Shift: GP Timer 2 is treated as an 8-bit or 16-bit timer: 0 = 8-bit; 1 = 16-bit.

As an 8-bit timer, the count value is loaded into GP Timer 2 Count Register (F0 Index 8Ah).

As a 16-bit timer, the value loaded into GP Timer 2 Count Register is shifted left by eight bits, the lower eight bits become

zero, and this 16-bit value is used as the count for GP Timer 2.

General Purpose Timer 1 Shift: GP Timer 1 is treated as an 8-bit or 16-bit timer: 0 = 8-bit; 1 = 16-bit.

As an 8-bit timer, the count value is that loaded into GP Timer 1 Count Register (F0 Index 88h).

As a 16-bit timer, the value loaded into GP Timer 1 Count Register is shifted left by eight bit, the lower eight bits become

zero, and this 16-bit value is used as the count for GP Timer 1.

Time Basis for General Purpose Timer 2: Selects timebase for GP Timer 2 (F0 Index 8Ah): 0 = 1 sec; 1 = 1 msec.

Re-trigger General Purpose Timer 2 on GPIO7 Pin Transition: A configured transition on the GPIO7 pin reloads GP

Timer 2 (F0 Index 8Ah): 0 = Disable; 1 = Enable.

F0 Index 92h[7] selects whether a rising- or a falling-edge transition acts as a reload. For GPIO7 to work here, it must first

be configured as an input (F0 Index 90h[7] = 0).

1:0

Reserved: Set to 0.

Table 3-27. General Purpose Timers and Control Registers (Continued)

Bit

Description

CS5530 数据表(PDF) 71 Page - National Semiconductor (TI)

CS5530 数据表(HTML) 71 Page - National Semiconductor (TI)

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100 ...More

数据表下载