CS5530 datasheet(178/241 Pages) NSC

178 / 241 page

www.national.com

178

Revision 4.1

Index F7h

Second Level Power Management Status Register 4 (RO/RC)

Reset Value = 00h

GPIO2 SMI Status (Read to Clear): SMI was caused by transition on (properly-configured) GPIO2 pin?

0= No; 1 = Yes.

This is the second level of SMI status reporting. The top level is reported in F1BAR+Memory Offset 00h/02h[0].

SMI generation enabling is at F0 Index 92h[2].

GPIO1 SMI Status (Read to Clear): SMI was caused by transition on (properly-configured) GPIO1 pin?

0= No; 1 = Yes.

This is the second level of SMI status reporting. The top level is reported in F1BAR+Memory Offset 00h/02h[0].

SMI generation enabling is at F0 Index 92h[1].

GPIO0 SMI Status (Read to Clear): SMI was caused by transition on (properly-configured) GPIO0 pin?

0= No; 1 = Yes.

This is the second level of SMI status reporting. The top level is reported in F1BAR+Memory Offset 00h/02h[0].

SMI generation enabling is at F0 Index 92h[0].

Lid Position (Read Only): This bit maintains the current status of the lid position. If the GPIO6 pin is configured as the lid

switch indicator, this bit reflects the state of the pin.

Lid Switch SMI Status (Read to Clear): SMI was caused by a transition on the GPIO6 (lid switch) pin?

0= No; 1 = Yes.

For this to happen, the GPIO6 pin must be configured both as an input (F0 Index 90h[6] = 0) and as the lid switch (F0

Index 92h[6] =1).

Codec SDATA_IN SMI Status (Read to Clear): SMI was caused by an AC97 codec producing a positive edge on

SDATA_IN? 0 = No; 1 = Yes.

This is the second level of status is reporting. The top level status is reported in F1BAR+Memory Offset 00h/02h[0].

SMI generation enabling is at F0 Index 80h[5].

RTC Alarm (IRQ8) SMI Status (Read to Clear): SMI was caused by an RTC interrupt? 0 = No; 1 = Yes.

This SMI event can only occur while in 3V Suspend and RTC interrupt occurs.

This is the second level of SMI status reporting. The top level is reported in F1BAR+Memory Offset 00h/02h[0].

ACPI Timer SMI Status (Read to Clear): SMI was caused by an ACPI Timer MSB toggle? 0 = No; 1 = Yes.

This is the second level of SMI status reporting. The top level is reported in F1BAR+Memory Offset 00h/02h[0].

SMI generation configuration is at F0 Index 83h[5].

Note: Properly-configured means that the GPIO pin must be enabled as a GPIO, an input, and to cause an SMI.

This register provides status on several miscellaneous power management events that generate SMIs, as well as the status of

the Lid Switch. Reading this register clears the SMI status bits. A read-only (mirror) version of this register exists at

F0 Index 87h.

Index F8h-FFh

Reserved

Table 4-14. F0 Index xxh: PCI Header and Bridge Configuration Registers (Continued)

Bit

Description

CS5530 数据表(PDF) 178 Page - National Semiconductor (TI)

CS5530 数据表(HTML) 178 Page - National Semiconductor (TI)

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100 ...More

数据表下载

链接网址

CS5530 数据表(PDF) 178 Page - National Semiconductor (TI)

CS5530 数据表(HTML) 178 Page - National Semiconductor (TI)

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100 ...More

数据表 下载

链接网址

数据表下载