CS5530 datasheet(203/241 Pages) NSC

203 / 241 page

Revision 4.1

203

www.national.com

28:24

5-Bit DCLK PLL Post Divisor (PD) Value: Selects value of 1 to 31:

00000 = PD divisor of 8

01000 = PD divisor of 10

10000 = PD divisor of 9

11000 = PD divisor of 11

00001 = PD divisor of 6

01001 = PD divisor of 20

10001 = PD divisor of 7

11001 = PD divisor of 21

00010 = PD divisor of 18

01010 = PD divisor of 14

10010 = PD divisor of 19

11010 = PD divisor of 15

00011 = PD divisor of 4

01011 = PD divisor of 26

10011 = PD divisor of 5

11011 = PD divisor of 27

00100 = PD divisor of 12

01100 = PD divisor of 22

10100 = PD divisor of 13

11100 = PD divisor of 23

00101 = PD divisor of 16

01101 = PD divisor of 28

10101 = PD divisor of 17

11101 = PD divisor of 29

00110 = PD divisor of 24

01110 = PD divisor of 30

10110 = PD divisor of 25

11110 = PD divisor of 31

00111 = PD divisor of 2

01111 = PD divisor of 1*

10111 = PD divisor of 3

11111 = RSVD

*See bit 11 description.

Plus 1 (+1): Adds 1 or 0 to FD (DCLK PLL VCO Feedback Divisor) parameter in equation (see Note):

0 = Add0 to FD; 1 = Add 1toFD

22:12

N: This bit represents “N” in the equation (see Note). It is used to solve the value of FD (DCLK PLL VCO Feedback Divi-

sor). N can be a value of 1 to 400. For all values of N, refer to Table 4-23.

CLK_ON: 0 = PLL disable; 1 = PLL enable. If PD = 1 (i.e., bits [28:24] = 01111) the PLL is always enabled.

DOT Clock Select: 0 = DCLK; 1 = TV_CLK.

Select Feedback Source: 0 = DPLL; 1 = FREF.

Bypass PLL: Connects the input of the PLL directly to the output of the PLL: 0 = Normal Operation; 1 = Bypass PLL.

If this bit is set to 1, the input of the PLL bypasses the PLL and resets the VCO control voltage, which in turn powers down

the PLL. Allow 0.5 ms for the control voltage to be driven to 0V.

7:6

Reserved: Set to 0.

PLL Lock Indictor: 0 = PLL has not locked on frequency; 1 = PLL has locked on frequency.

4:3

Reserved: Set to 0.

2:0

PLL Input Divide (ID) Value: Selects value of 2 to 9 (see Note):

000 = ID divisor of 2

100 = ID divisor of 6

001 = ID divisor of 3

101 = ID divisor of 7

010 = ID divisor of 4

110 = ID divisor of 8

011 = ID divisor of 5

111 = ID divisor of 9

Note:

To calculate DCLK output frequency:

Equation #1: DCLK = [CLK_14MHZ * FD] ÷ [PD *ID]

Condition: 140 MHz < [DCLK * PD] < 300 MHz

Where:

CLK_14MHZ is pin P24

FD is derived from N see equation #2 and #3:

PD is derived from bits [28:24]

ID is derived from bits [2:0]

Equation #2: If FD is an odd number then: FD = 2*N +1

Equation #3: If FD is an even number then: FD = 2*N +0

Where:

N is derived from bits [22:12]

+1 is achieved by setting bit 23 to 1.

+0 s achieved by clearing bit 23 to 0.

Table 4-22. F4BAR+Memory Offset xxh: Video Controller Configuration Registers (Continued)

Bit

Description

CS5530 数据表(PDF) 203 Page - National Semiconductor (TI)

CS5530 数据表(HTML) 203 Page - National Semiconductor (TI)

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100 ...More

数据表下载