| 数据搜索系统,热门电子元器件搜索 |
|
CS5530 数据表(PDF) 105 Page - National Semiconductor (TI) |
|
|
|
|||||||||||||||||||||||||||||
CS5530 数据表(HTML) 105 Page - National Semiconductor (TI) |
|
105 / 241 page ![]() Revision 4.1 105 www.national.com Functional Description (Continued) 3.6 IDE CONTROLLER The CS5530 integrates a fully-buffered, 32-bit, ANSI ATA- 4-compliant (Ultra DMA/33) IDE interface. The IDE inter- face supports two channels, primary and secondary, each supporting two devices that can operate in PIO Modes 1, 2, 3, 4, Multiword DMA, or Ultra DMA/33. The IDE interface provides a variety of features to opti- mize system performance, including 32-bit disk access, post write buffers, bus master, Multiword DMA, look- ahead read buffer, and prefetch mechanism for each channel respectively. The IDE interface timing is completely programmable. Timing control covers the command active and recover pulse widths, and command block register accesses. The IDE data-transfer speed for each device on each channel can be independently programmed allowing high-speed IDE peripherals to coexist on the same channel as older, compatible devices. The CS5530 also provides a software-accessible buffered reset signal to the IDE drive, F0 Index 44h[3:2] (Table 3- 53). The IDE_RST# signal is driven low during reset to the CS5530 and can be driven low or high as needed for device-power-off conditions. 3.6.1 IDE Interface Signals The CS5530 has two completely separate IDE control sig- nals, however, the IDE_RST#, IDE_ADDR[2:0] and IDE_DATA[15:0] are shared. The connections between the CS5530 and IDE devices are shown as Figure 3-19. Figure 3-19. CS5530 and IDE Channel Connections Table 3-53. IDE Reset Bits Bit Description F0 Index 44h Reset Control Register (R/W) Reset Value = xx000000b 3 IDE Controller Reset: Reset the IDE Controller: 0 = Disable; 1 = Enable. Write 0 to clear. This bit is level-sensitive and must be cleared after the reset is enabled. 2 IDE Reset: Reset IDE bus: 0 = Disable; 1 = Enable. Write 0 to clear. This bit is level-sensitive and must be cleared after the reset is enabled. IDE_ADDR[2:0] IRQ14 IRQ15 IDE_DATA[15:0] Primary Channel Secondary Channel IDE_RST# IDE_CS0#, IDE_DREQ0, IDE_DACK0#, IDE_IORDY0, IDE_IOR0#, IDE_IOW0# IDE_CS1#, IDE_DREQ1, IDE_DACK1#, IDE_IORDY1, IDE_IOR1#, IDE_IOW1# |
|
链接网址 |
| ALLDATASHEET是否为您带来帮助? [ DONATE ] |
关于 Alldatasheet | 广告服务 | 联系我们 | 隐私政策 | 数据表链接 | 链接交换 | 制造商名单 All Rights Reserved©Alldatasheet.com |
| Russian : Alldatasheetru.com | Korean : Alldatasheet.co.kr | Spanish : Alldatasheet.es | French : Alldatasheet.fr | Italian : Alldatasheetit.com Portuguese : Alldatasheetpt.com | Polish : Alldatasheet.pl | Vietnamese : Alldatasheet.vn Indian : Alldatasheet.in | Mexican : Alldatasheet.com.mx | British : Alldatasheet.co.uk | New Zealand : Alldatasheet.co.nz |
|
Family Site : ic2ic.com |
icmetro.com |